Mechanical engineering topic list of research papers
-
CFD Modelling of Flame Stretch in SI Engines
Abstract The flame stretch is a phenomenon that affects the combustion initial stage in premixed charge Spark-Ignition (SI) engines with consequences on the laminar burning velocity, so its correct description is fundamental to predict the further...
2015 / Lorenzo Sforza, Tommaso Lucchini, Angelo Onorati -
Tailoring Strongly Nonlinear Negative Stiffness2013 / F. Liu, S. Theodossiades, D. M. McFarland, A. F. Vakakis, L. A. Bergman
-
On Thermal Performance of Seawater Cooling Towers2010 / Mostafa H. Sharqawy, John H. Lienhard, Syed M. Zubair
-
A Novel Hybrid Rehabilitation Device for Neuromuscular Control Exercise and Rehabilitation Training
Abstract W-vibe neuromuscular control ankle rehabilitation device is designed based on the principle of a single leg stance activity. It aims to enhance the balancing level of the individuals and re-establishing neuromuscular control for ankle...
2015 / Hadafi Fitri Mohd Latip, Abdul Hafidz Omar, Ardiyansyah Shahrom, Fakhrizal Azmi, Ridhwan -
Three dimensional numerical simulations for non-breaking solitary wave interacting with a group of slender vertical cylinders2015 / Weihua Mo, Philip L.-F. Liu
-
A Review of Experimental Techniques for NVH Analysis on a Commercial Vehicle
Abstract Noise and vibration of automotive vehicles are an increasingly important issue in the automobile industry, for implications on both environmental noise pollution and comfort perceived by driver and passengers. Since noise and vibration...
2015 / Maria Antonietta Panza -
CFD Study on Convective Heat Exchange between Impinging Gas Jets and Solid Surfaces
Abstract The paper is concerned with a CFD numerical investigation using the Fluent code of the convective heat exchange between an impinging gas jet at room temperature and a structured solid surface with square-shaped grooves which is maintained...
2016 / Ştefan-Mugur Simionescu, Corneliu Bălan -
Multiobjective Optimization of the Breathing System of an Aircraft two Stroke Supercharged Diesel Engine
Abstract One of the factors limiting the utilization of piston internal combustion engines for aircraft propulsion is the performance decrease increasing the altitude of operation. This is due to the negative effect of air density reduction...
2015 / Antonio Paolo Carlucci, Antonio Ficarella, Domenico Laforgia, Gianluca Trullo -
Adaptive parameters for tracking filters innovation system2016 / C.-M. Wu
-
Defect analysis in drilling needle-punched carbon-carbon composites perpendicular to nonwoven fabrics2015 / C. Shan, X. Lin, X. Wang, J. Yan, D. Cui
-
Robotic neurorehabilitation system design for stroke patients2015 / B. Xu, A. Song, G. Zhao, G. Xu, L. Pan, et al.
-
Impact motion control of humanoid robot BHR-5 based on the energy integral method2016 / F. Meng, X. Chen, Z. Yu, X. Chen, M. Zhou, et al.
-
Progress toward a DoD Ground Vehicle Tradespace and Affordability Analysis Framework
Abstract During ground system conceptual design and engineering development many tradeoff decisions are made to balance functional performance, cost, risk, robustness, reliability, interoperability, growth margin, and other life-cycle...
2015 / Gary Witus, Walter Bryzik -
Blade profile optimization of pump as turbine2015 / S.-c. Miao, J.-h. Yang, G.-t. Shi, T.-t. Wang
-
Modeling and calculation of variable moment of inertia for spiral power spring2015 / Y. Yu, Z. Mi, X. Guo
-
A Numerical Model to Study the Role of Surface Textures at Top Dead Center Reversal in the Piston Ring to Cylinder Liner Contact2015 / N. Morris, R. Rahmani, H. Rahnejat, P. D. King, S. Howell-Smith
-
Numerical Modelling of Surface Quality in EDM Processes
Abstract Electro-discharge machining (EDM) is a non-conventional cutting technology widely applied to generate mechanical parts with a complex geometry. In order to describe the thermo-physical phenomena involved in this process and estimate the...
2015 / C. Mascaraque-Ramirez, P. Franco -
Cutting forces during turning with variable depth of cut
Summary The purpose of this paper is to investigate the problems with increasing the efficiency of turning cycles. This paper also describes and suggests the possibility of using effective strategies and their application in programming CNC turning...
2015 / M. Sadílek, J. Dubský, Z. Sadílková, Z. Poruba -
Effects of capillary pressure – fluid saturation – relative permeability relationships on predicting carbon dioxide migration during injection into saline aquifers
Abstract Mathematical modeling and numerical simulations on carbon dioxide plume migration in confined saline aquifers have become important approaches to evaluate storage capacity and efficiency for carbon dioxide sequestration and to predict...
2014 / Yongzhong Liu, Le Wang, Xiaoyu Liu, Tian Ding -
Simplified Approach to the Prediction and Analysis of Temperature Inhomogeneity in Rapid Compression Machines2015 / Sajjad Yousefian, François Gauthier, Amadeo Morán-Guerrero, Robert R. Richardson, Henry J. Curran, et al.