Mechanical engineering topic list of research papers
-
Analysis of swirling flow effects on the characteristics of unsteady hot-streak migration
Abstract The temperature of flow at the combustor exit is inherently non-uniform and the hot fluid is called hot-streak. An in-house CFD software, NUAA-Turbo, was used to carry out 3D unsteady simulations on the PW-E3 single-stage high-pressure...
2016 / Jingyu Wang, Ning Ge, Chunhua Sheng -
Experimental and numerical study of a bird strike against a windshield2015 / Fabien Plassard, Pierre-Louis Hereil, Pierric Joseph, Jérôme Mespoulet
-
A simple and novel way of maintaining constant wall temperature in microdevices2016 / V. S. Duryodhan, Abhimanyu Singh, Shiv Govind Singh, Amit Agrawal
-
Active control on high-order coherence and statistic characterization on random phase fluctuation of two classical point sources2016 / Peilong Hong, Liming Li, Jianji Liu, Guoquan Zhang
-
The limitations on applying classical thin plate theory to thin annular plates clamped on the inner boundary2012 / Daniel W. Zietlow, Donald C. Griffin, Thomas R. Moore
-
Haptic Edge Detection Through Shear2016 / Jonathan Platkiewicz, Hod Lipson, Vincent Hayward
-
Working fluid flow visualization in gravity heat pipe2016 / Patrik Nemec, Milan Malcho
-
Modeling and simulation of the zinc-nickel single flow batteries based on MATLAB/Simulink2016 / Shouguang Yao, Peng Liao, Min Xiao, Jie Cheng, Ke He
-
The experimental study of heat extraction of supercritical CO2in the geothermal reservoir2016 / Cyun-Jie Huang, Jui-Ching Hsieh, David T. W. Lin, Jenn-Kun Kuo, Yuh-Chung Hu
-
A Simulation Study of Recessed Type Hydrostatic Journal Bearing2016 / Shih-Ming Wong, Ta-Hua Lai, Min-Cheng Lin, Shih-Chieh Lin
-
Simulation of viscous melt drop crystallization by the SPH method2016 / Alexander V. Gerasimov, Roman O. Cherepanov, Raisa A. Krektuleva, Vladimir N. Barashkov
-
Image Processing Assisted Tools for Pre- and Post-processing Operations in Additive Manufacturing
Abstract Additive Manufacturing (AM) or 3D printing (3DP) process is a layer by layer manufacturing approach for manufacturing parts with complex geometries. The STL (Stereolithography) file format is the de-facto industry standard for manufacturing ...
2016 / Rohit Vaidya, Sam Anand -
Effects of play and inerter nonlinearities on the performance of tuned mass damper2016 / P. Brzeski, P. Perlikowski
-
Development and identification of rheological model adapted for Powder Injection Moulding2016 / Dimitri Claudel, Mohamed Sahli, Thierry Barriere, Jean-Claude Gelin
-
A motion sensing-based framework for robotic manipulation2016 / Hao Deng, Zeyang Xia, Shaokui Weng, Yangzhou Gan, Peng Fang, et al.
-
Investigation of Energy Efficient Power Coupling Steering System for Dual Motors Drive High Speed Tracked Vehicle
Abstract This paper presents an energy efficient power coupling steering system for dual motors drive high speed tracked vehicle. The system consists of a new type of center steering motor, two electromagnetic (EM) clutches, two planetary gear...
2016 / Li Zhai, Hong Huang, Tianmin Sun, Qiannan Wang -
Numerical modeling of 1D heterogeneous combustion in porous media under free convection taking into account dependence of permeability on porosity2016 / N A Lutsenko
-
Approach to novel design of CO2based centrifugal compressor2016 / Tomasz Kura, Elżbieta Fornalik-Wajs
-
Semi-Active Vibration Control of Laminated Composite Sandwich Plate – An Experimental Study2016 / R. Manoharan, R. Vasudevan, P. Edwin Sudhagar
-
Shale gas flowback water desalination: Single vs multiple-effect evaporation with vapor recompression cycle and thermal integration
Abstract This paper introduces a new optimization model for the single and multiple-effect evaporation (SEE/MEE) systems design, including vapor recompression cycle and thermal integration. The SEE/MEE model is specially developed for shale gas...
2016 / Viviani C. Onishi, Alba Carrero-Parreño, Juan A. Reyes-Labarta, Rubén Ruiz-Femenia, Raquel Salcedo-Díaz, et al.