Mechanical engineering topic list of research papers
-
Parametric Optimization of Brayton /Organic Trans-critical Combined Cycle for Flue Gas Waste Heat Recovery
Abstract A combined cycle composed of an air based open Brayton cycle (BC) and an organic trans-critical cycle (OTC) is presented for power recovery from flue gas of initial temperature around 600°C. BC is employed as the top cycle to span the...
2015 / Chengyu Li, Qiang Zhu, Huaixin Wang -
The Electrochemical Machining Analysis of Aeroengine Blade Based on Isogeometric Method2015 / N. Wan, K. Du, R. Mo, T. Chen
-
Film Cooling Performance in a Transonic High-pressure Vane: Decoupled Simulation and Conjugate Heat Transfer Analysis
Abstract The continuous demand for increased performance and reliability of gas turbines leads to the improvement of prediction tools. Having regard to the effects of heat transfer on the residual life of gas turbine components, it is necessary to...
2014 / Massimiliano Insinna, Duccio Griffini, Simone Salvadori, Francesco Martelli -
Stack Parameters Effect on the Performance of Anharmonic Resonator Thermoacoustic Heat Engine2014 / Mostafa A. Nouh, Nadim M. Arafa, Ehab Abdel-Rahman
-
Application of Dimethyl Ether as LPG Substitution for Household Stove
Abstract Dimethyl Ether (DME) has potency for substituting LPG for household. Indonesia is rich of the sources of DME so DME usage becomes very attractive. The experiments performed in Research and Development Center for Oil and Gas Technology...
2014 / Riesta Anggarani, Cahyo S. Wibowo, Dimitri Rulianto -
Dye Transport Pattern in Compound Vortex Flow
Abstract Shapes of deformed water surface and transport of dyes in compound vortex flow are studied experimentally. Vortex motion is produced by rotating disc at the bottom of vertical cylindrical container. Strong anisotropy of substance transport...
2013 / E.V. Stepanova -
A case study on compatibility of automotive exhaust thermoelectric generation system, catalytic converter and muffler
Abstract The power generation of an exhaust TEG (thermoelectric generator) depends on heat energy and thermoelectric conversion efficiency. However, there are compatibility problems among TEG, CC (catalytic converter) and muf (muffler). The present...
2014 / X. Liu, Y.D. Deng, S. Chen, W.S. Wang, Y. Xu, et al. -
Blended Wing Body Architecting and Design: Current Status and Future Prospects
Abstract Fixed-wing aircraft are viewed as no longer satisfying our needs today. In the past ten years, fuel efficiency and noise reduction have become the two biggest challenges for aircraft manufacturers. The recognition spurred aerospace...
2014 / Edwin Ordoukhanian, Azad M. Madni -
An Information Model for Product Development: A Case Study at PHILIPS Shavers
Abstract This paper presents an investigation into the development of an information model to support the Product Development Process (PDP) of shaving devices at PHILIPS. Firstly, challenges of the PDP were identified by carrying out interviews with ...
2013 / Juan M. Jauregui-Becker, Wessel W. Wits -
Fostering in-process Inspection During Process Planning Using Tolerance Charting
Abstract Integrated development of machining and inspection plans is essential in dynamic manufacturing environments, especially when right first time manufacturing is required. In this work, a methodology, based on a new and extended use of...
2013 / G.M. Bruscas, F. Romero, P. Rosado, J. Serrano -
Matching of Suspension Damping and Air Spring Based on Multi-Body Dynamic Model
Abstract By using multi-body dynamics simulation software SIMPACK, the paper completed full vehicle modeling of bus air suspension. In four typical working conditions, body vertical acceleration, suspension working space and dynamic tire load were...
2012 / Shaohua Wang, Chunfang Yin, Huawei Zhao -
A Real-time NURBS Surface Interpolator for 5-axis Surface Machining
Abstract A real-time non-uniform rational B-spline (NURBS) surface interpolator is proposed and 5-axis machining method with a flat-end cutter is discussed. With the Taylor expansion and the coordinate transformation, the, algorithms of NURBS...
2011 / Yong-zhang WANG, Liang-ji CHEN -
Design of a Highly Maneuverable Mobile Robot
Abstract Designing a robust, modular and fast mobile robot which can work in challenging environment is a difficult task. That includes design of mechanical parts and control system of the robot. This paper proposes a new design of mobile robot,...
2012 / R. Shah, S. Ozcelik, R. Challoo -
Resúmenes en Inglés English Abstracts2012 /
-
The Wear Measurement Process of Ball Nose end Mill in the Copy Milling Operations
Abstract The article deals with tool wear and the cutting tool wear measurement process of ball nose end mill in the copy milling. In the experiment, we studied cutting tool wear for different types of copy milling operations. The aim was to...
2014 / Vopát Tomas, Peterka Jozef, Kováč Mario, Buranský Ivan -
The Analysis of Traffic Control Cyber-physical Systems
Abstract Cyber-physical systems offer a new theory to the application of information to improve traffic control system performance. This paper, oriented to the integration of information and transportation processes, discusses the gateway role of...
2013 / Shi Jianjun, Wu Xu, Guan Jizhen, Chen Yangzhou -
Multi-stage Linear Programming Optimization for Pump Scheduling
Abstract This study presents a methodology based on Linear Programming for determining the optimal pump schedule on a 24-hour basis, considering as decision variables the continuous pump flow rates which are subsequently transformed into a discrete...
2014 / V. Puleo, M. Morley, G. Freni, D. Savić -
Performance Analysis in Off-design Condition of Gas Turbine Air-bottoming Combined System
Abstract Nowadays, the gradual depletion of fossil fuels associated with constraints on emissions of greenhouse gases leads to valorize their wasted heat from power plant. One of the technologies adopted for improvement is the utilization of...
2014 / Carlo Carcasci, Federico Costanzi, Beniamino Pacifici -
System Dynamics Model of Shanghai Passenger Transportation Structure Evolution
Abstract Based on the data from a comprehensive transportation survey of Shanghai in 2004 and 2009, this paper analyzed the evolution of urban passenger transportation structure using the system dynamics approach. A system dynamics model of Shanghai ...
2013 / Yang Chao, Miao Zishan -
On the Efficacy of PCM to Shave Peak Temperature of Crystalline Photovoltaic Panels: An FDM Model and Field Validation2013 / Valerio Lo Brano, Giuseppina Ciulla, Antonio Piacentino, Fabio Cardona