Mechanical engineering topic list of research papers
-
Defect Detection for Wheel-Bearings with Time-Spectral Kurtosis and Entropy2014 / Bin Chen, Zhaoli Yan, Wei Chen
-
A parametric study of lycopodium dust flame2015 / Mehdi Bidabadi, Hossein Beidaghy Dizaji, Farzad Faraji Dizaji, Seyed Alireza Mostafavi
-
Magnetohydrodynamic mixed convective slip flow over an inclined porous plate with viscous dissipation and Joule heating
Abstract The combined effects of viscous dissipation and Joule heating on the momentum and thermal transport for the magnetohydrodynamic flow past an inclined plate in both aiding and opposing buoyancy situations have been carried out. The governing ...
2015 / S. Das, R.N. Jana, O.D. Makinde -
Small scale effect on linear vibration of buckled size-dependent FG nanobeams
Abstract The thermal stress due to the temperature rise in micro/nano-beams with immovable ends produces compressive axial force which can lead to buckling the beams if its value increases over the critical value. Hence, the investigation of...
2015 / Sima Ziaee -
Energy and Force Analysis of Ti-6Al-4V Linear Friction Welds for Computational Modeling Input and Validation Data2014 / Anthony R. McAndrew, Paul A. Colegrove, Adrian C. Addison, Bertrand C. D. Flipo, Michael J. Russell
-
An Experimental Investigation of Showerhead Film Cooling Performance on a Turbine Blade
Abstract Experimental tests were performed to investigate the film cooling performance at the leading edge region of a turbine blade using the Infrared Radiation (IR) thermography technique. The test blades were enlarged by five times the natural...
2015 / Zhu Xingdan, Zhang Jingzhou, Tan Xiaoming -
Mode control of guided wave in magnetic hollow cylinder using electromagnetic acoustic transducer array
Abstract The aim of this work is to demonstrate a method for exciting and receiving torsional and longitudinal mode guided waves with an electromagnetic acoustic transducer (EMAT) ring array. First of all, a three-dimensional...
2015 / Akinori Furusawa, Fumio Kojima, Atsushi Morikawa -
Changing law of launching pitching angular velocity of rotating missile
Abstract In order to provide accurate launching pitching angular velocity (LPAV) for the exterior trajectory optimization design, multi-flexible body dynamics (MFBD) technology is presented to study the changing law of LPAV of the rotating missile...
2014 / Guang Liu, Bin Xu, Xiaojuan Jiao, Tiesheng Zhen -
Use of Cyclic Symmetry Properties in Vibration Analysis of Bladed Disks with Friction Contacts between Blades
Abstract The development of steam turbine's blades is closely related to the computer modelling of their vibrations. In this work, a numeric method that (i) implements the calculation of nonlinear vibrations (ii) makes use of the cyclic symmetry of...
2014 / Josef Voldřich, Pavel Polach, Jan Lazar, Tomáš Míšek -
Investigation of the effects of Stewart platform-type industrial robot on stability of robotic milling2016 / L. T. Tunc, Jay Shaw
-
Co-operative ITS: Smartphone based Measurement Systems for Road Safety Assessment
Abstract Co-operative Intelligent Transportation Systems (C-ITS) are attracting a lot of attention, and many resources are devoted to the development of new platforms integrating vehicle-to-vehicle (V2V) and vehicle-to-infrastructure (V2I)...
2014 / Vittorio Astarita, Giuseppe Guido, Vincenzo Pasquale Giofrè -
Study on the Vortex Structure of Coupling Combustion Stabilizer with Square Cylinder-strong Swirl Flow
Abstract Strong swirl and a blunt body are two commonly used structure to form low velocity recirculation zone to stabilize combusting of high-speed gas. Compared with the vortex shedding mechanism of the square cylinder blunt, the computational...
2015 / Gan Dong, Zhiqiang Li, Zhihong Zhang -
Process Simulation and Thermodynamic Analysis of a Micro Turbine with Post-combustion CO2 Capture and Exhaust Gas Recirculation
Abstract With the effects of the emissions from power plants causing global climate change, the trend towards lower emission systems such as natural gas power plant is increasing. In this paper a Turbec T100 micro gas turbine is studied. The system...
2014 / Usman Ali, Thom Best, Karen N. Finney, Carolina Font Palma, Kevin J. Hughes, et al. -
Design of a New In-Pipe Inspection Robot
Abstract Basically robots are designed in such way that they remove human intervention from labour intensive and hazardous work environment, sometimes they are also used to explore inaccessible work places which are generally impossible to access by ...
2014 / Ankit Nayak, S.K. Pradhan -
The paraconsistent process order control method2013 / Kazumi Nakamatsu, Jair M. Abe
-
Micro-blog Information Regulatory Mechanism based on Ontology Modeling
Abstract With the rapid development, micro-blog has become a social phenomenon, and the micro-blog supervision is imperative. The existing micro-blog information regulation relies on the user's self-regulation and legislation, and it's rarely...
2013 / Baoxiang Xu, Xinyuan Wang, Shu Zhang -
Life Cycle Assessment of a Diesel Engine Based on an Integrated Hybrid Inventory Analysis Model
Abstract This paper conducts a Life Cycle Assessment (LCA) to evaluate the energy consumptions and environmental emissions of an engine with Integrated Hybrid Life Cycle Inventory (IH-LCI) analysis method. Aggregated Input–Output matrix ...
2014 / Qiuhong Jiang, Zhichao Liu, Tao Li, Hongchao Zhang, Asif Iqbal -
Congestion Service Facilities Location Problem with Promise of Response Time2013 / Dandan Hu, Zhi-Wei Liu, Wenshan Hu
-
Development of a Landing Mechanism for Asteroids with Soft Surface2013 / Zhijun Zhao, Jingdong Zhao, Hong Liu
-
Semi-Analytical Solution Based on Strip Method for Buckling and Vibration of Isotropic Plate2013 / Mohamed A. El-Sayad, Ahmed M. Farag