Mechanical engineering topic list of research papers
-
A Back-stepping Based Trajectory Tracking Controller for a Non-chained Nonholonomic Spherical Robot
Abstract Spherical robot has good static and dynamic stability, which provides it with strong viability in hostile environment, but the lack of effective control methods has hindered its application and development. This article deals with the...
2008 / Zhan Qiang, Liu Zengbo, Cai Yao -
Autonomous mobile robot localization using Kalman filter2016 / Nabil Zhafri Mohd Nasir, Muhammad Aizzat Zakaria, Saifudin Razali, Mohd Yazid bin Abu
-
Experimental Analysis and Feasibility Study of 1400 CC Diesel Engine Car Converted into Hybrid Electric Vehicle by Using BLDC Hub Motors
Abstract New generation HEV (hybrid electric vehicles) are targeting for reducing exhaust gas pollution by operating in EV (electric vehicle) mode during the stop and go movement in thick traffic conditions at low engine rpm, but run on ICE...
2014 / Sudhir Gupte -
Experimental investigation of supersonic flow over elliptic surface2013 / Qinghu Zhang, Shihe Yi, Lin He, Yangzhu Zhu, Zhi Chen
-
Combustion time of the oxygenated and non-oxygenated fuels in an Otto cycle engine2013 / Pedro Mello, Fabiano Wildner, Giovanni Souza de Andrade, Renato Cataluña, Rosângela da Silva
-
Study on Objective Evaluation Method of Taxi Driver Safety Consciousness
Abstract This study aims to conduct researches on the correlation between driver safety consciousness and several indices, and propose an objective evaluation criterion, which can covert immeasurable safety consciousness to measurable objective...
2014 / Weihua Zhao, Wei Han, Ying Wen, Dongmei Zhang -
Sub-scale Machining of Large Components
Abstract A post-processing algorithm for CNC machine NC code was developed for altering NC code based on measurements from a stand-alone coordinate metrology system that measures the orientation and offset of the part and machine coordinate systems...
2015 / Paul Anderson, John Ziegert -
Experimental Study on the High Speed Machining of Hardened Steel
Abstract In the present paper, experimental study is made to investigate the effect of cutting parameters on surface roughness in dry high speed milling of hardened tool steel using two cutting tools (diameter of 20 and 40mm). The cutting parameters ...
2014 / Derzija Begic-Hajdarevic, Ahmet Cekic, Malik Kulenovic -
An intelligent control method for a large multi-parameter environmental simulation cabin
Abstract The structure and characteristics of a large multi-parameter environmental simulation cabin are introduced. Due to the difficulties of control methods and the easily damaged characteristics, control systems for the large multi-parameter...
2013 / Ke Li, Wangkai Liu, Jun Wang, Yong Huang -
Development of a Technology-based Design Environment Focused on Improving User Experience
Abstract Computer tools usage has became one of the major trends in humanity and product design processes are not stranger to this situation. That is the reason why different computer tools (hardware and software) have been developed in order to...
2014 / David Ríos-Zapata, Gilberto Osorio-Gómez, Ricardo Mejía-Gutiérrez -
Research for Hybridization Degree and Logic Threshold Control Strategy of the Hybrid Power Gas Engine Heat Pump
Abstract Gas engine heat pump is the important distributed power supply system in the energy structure. Hybrid power technique plays an important role to improve the engine performance and the gas conversion efficiency of gas engine heat pump...
2015 / Wenxiu Ji, Liang Cai, Qinkun Men, GaoFeng Sun, Xiaosong Zhang -
Experimental and Numerical Investigation of the Effects of Passive Vortex Generators on Aludra UAV Performance
Abstract A study of the effects of passive vortex generators (VGs) on Aludra unmanned aerial vehicle (UAV) aerodynamic characteristics is presented. Both experimental and numerical works are carried out where an array of VGs is attached on Aludra...
2011 / Tan Kar ZHEN, Muhammed ZUBAIR, Kamarul Arifin AHMAD -
The optimization of On-ramp Junction Capacity based on Zippered Control Strategy
Abstract Traffic congestion on on-ramp metered areas will increase the delay and reduce the capacity of urban elevated road dramatically. The method of alternate driving has the function of increasing the capacity of the on-ramp metered areas under...
2013 / Huadong Tan, Xiaoguang Yang, Aoxiang Wu -
Metal Additive Manufacturing of a High-pressure Micro-pump
Abstract For the thermal control of future space applications pumped two-phase loops are an essential part to handle the increasing thermal power densities. This study investigates the design of a reliable, leak tight, low-weight and high-pressure...
2013 / Wessel W. Wits, Sander J. Weitkamp, Johannes van Es -
Experimental Investigation of Heat Transfer and Pressure Drop Characteristics of H-type Finned Tube Banks2014 / Heng Chen, Yungang Wang, Qinxin Zhao, Haidong Ma, Yuxin Li, et al.
-
Study of the Algorithm of Backtracking Decoupling and Adaptive Extended Kalman Filter Based on the Quaternion Expanded to the State Variable for Underwater Glider Navigation2014 / Haoqian Huang, Xiyuan Chen, Zhikai Zhou, Yuan Xu, CaiPing Lv
-
An Embedded Stress Sensor for Concrete SHM Based on Amorphous Ferromagnetic Microwires2014 / Jesús Olivera, Margarita González, José Fuente, Rastislav Varga, Arkady Zhukov, et al.
-
Multi-Objective Structural Optimization Design of Horizontal-Axis Wind Turbine Blades Using the Non-Dominated Sorting Genetic Algorithm II and Finite Element Method2014 / Jie Zhu, Xin Cai, Pan Pan, Rongrong Gu
-
Fast and Flexible Movable Vision Measurement for the Surface of a Large-Sized Object2015 / Zhen Liu, Xiaojing Li, Fengjiao Li, Xinguo Wei, Guanjun Zhang
-
Optimal Thermal Design of a Stacked Mini-Channel Heat Sink Cooled by a Low Flow Rate Coolant2013 / Liping Pang, Minxing Wang, Wei Wang, Meng Liu, Jun Wang