Mechanical engineering topic list of research papers
-
Modeling of large scale solar cell handling robot with belt-driven flexible arms
Abstract To increase the competition of the solar energy collection system, the size of the solar panel module during the manufacturing process is being increased continuously. As the size of the solar panel increases, the size of the robot to...
2013 / Eun Yim Cho, Jinsu Kim, Sungsoo Rhim -
Green Fuel Design for Diesel Engine, Combustion, Performance and Emission Analysis
Abstract Vegetable oils are a potential alternative to the partial or total substitution of diesel fuels. An experimental investigation is conducted to evaluate the effects of using ethanol and diethyl ether as additives to biodiesel/diesel blends...
2013 / T. Pushparaj, S. Ramabalan -
Research of low boom and low drag supersonic aircraft design
Abstract Sonic boom reduction will be an issue of utmost importance in future supersonic transport, due to strong regulations on acoustic nuisance. The paper describes a new multi-objective optimization method for supersonic aircraft design. The...
2014 / Xiaoqiang Feng, Zhanke Li, Bifeng Song -
Modeling Pedestrian Delay at Signalized Intersection Crosswalks Under Mixed Traffic Condition
Abstract Walking is one of the main and sustainable traffic mode in urban transportation, particularly in India because of the flexibility and mobility involved in it. Pedestrians are facing problems during crossing at signalized intersection...
2013 / S. Marisamynathan, P. Vedagiri -
Tool Path Generation for Clean-up Machining of Impeller by Point-searching Based Method
Abstract Machining quality of clean-up region has a strong influence on the performances of the impeller. In order to plan clean-up tool paths rapidly and obtain good finish surface quality, an efficient and robust tool path generation method is...
2012 / Ming TANG, Dinghua ZHANG, Ming LUO, Baohai WU -
Study on Subjective and Objective Safety and Application of Expressway
Abstract According to the research of the subjective and the objective safety in Highway Safety Manual (HSM), their relationship and the road safety were discussed and improved. In this paper, the contents and the calculation methods of the...
2013 / Zhizhong Li, Xiaohuan Zhou, Xiaoan Wang, Zhongyin Guo -
A Requirements Management System based on an Optimization Model of the Design Process
Abstract In this paper, the engineering design process is modeled as an optimization problem over the system design space, where the goals, desired outcomes, and trade-off preferences of the customer define measurable objective functions. In this...
2014 / Nathan W. Mogk -
Preliminary Study on Streamlined Design of Longitudinal Profile of High-speed Train Head Shape
Abstract The effect of high-speed train head shape on its aerodynamic performance is very important. In order to prove the effect of longitudinal profile shape of train head on aerodynamic performance, using CFD method, a two dimension model is...
2013 / Xinwen Yang, Jielong Jin, Guangtian Shi -
An integrated graphic–taxonomic–associative approach to analyze human factors in aviation accidents
Abstract Human factors are critical causes of modern aviation accidents. However, existing accident analysis methods encounter limitations in addressing aviation human factors, especially in complex accident scenarios. The existing graphic...
2014 / Lei Gong, Shuguang Zhang, Peng Tang, Yi Lu -
Experimental Investigation of Noise Pollution Level Emerged from the Most Common use Car in Saudi Arabia
Abstract The present study documents noise pollution levels measured for the most common cars used by people in Saudi Arabia. The noise levels were measured following standard procedure by using calibrated sound pressure level meter at all sides of...
2013 / Khaled S. AlQdah -
A Versatile Method to Determine Thermal Limits in Grinding
Abstract This paper discusses a physical based method to determine limits with regard to the thermal impact of grinding processes on the machined workpiece surface layer. The thermal limits can be identified by analyzing the specific grinding power...
2014 / C. Heinzel, J. Sölter, S. Jermolajev, B. Kolkwitz, E. Brinksmeier -
Analysis and Performance of ORC Based Solar Thermal Power Plant Using Benzene as a Working Fluid
Abstract In the present scenario of huge demand of energy and economy create the necessity to give importance to all types of energy resources either it is conventional or nonconventional. Since the rapid consumption of fossil fuel over billions of...
2016 / Arun Kumar, S.K. Shukla -
Hand-Writing Motion Tracking with Vision-Inertial Sensor Fusion: Calibration and Error Correction2014 / Shengli Zhou, Fei Fei, Guanglie Zhang, Yunhui Liu, Wen Li
-
Wayside Bearing Fault Diagnosis Based on a Data-Driven Doppler Effect Eliminator and Transient Model Analysis2014 / Fang Liu, Changqing Shen, Qingbo He, Ao Zhang, Yongbin Liu, et al.
-
Determination of optimal samples for robot calibration based on error similarity
Abstract Industrial robots are used for automatic drilling and riveting. The absolute position accuracy of an industrial robot is one of the key performance indexes in aircraft assembly, and can be improved through error compensation to meet...
2015 / Wei Tian, Dongqi Mei, Pengcheng Li, Yuanfan Zeng, Peng Hong, et al. -
Analysis of Functional Architectures for Discrete Event Logistics Systems (DELS)
Abstract The functional design of discrete event logistics systems (DELS) specifies the systems’ transformative functions independently from the technology required to implement those functions. Creating a functional architecture for a new system is ...
2015 / Timothy Sprock, Leon F. McGinnis -
Vacuum Insulation Panels: Analysis of the Thermal Performance of Both Single Panel and Multilayer Boards2015 / Alfonso Capozzoli, Stefano Fantucci, Fabio Favoino, Marco Perino
-
Fuzzy norm method for evaluating random vibration of airborne platform from limited PSD data
Abstract For random vibration of airborne platform, the accurate evaluation is a key indicator to ensure normal operation of airborne equipment in flight. However, only limited power spectral density (PSD) data can be obtained at the stage of flight ...
2014 / Zhongyu Wang, Yanqing Wang, Qian Wang, Jianjun Zhang -
Three-dimensional numerical simulation of a vortex ring impacting a bump
Abstract A vortex ring impinging on a three-dimensional bump is studied using large eddy simulation for a Reynolds number Re = 4 × 104 based on the initial translation speed and diameter of the vortex ring. The effects of bump height on the vortical ...
2014 / Heng Ren, Changyue Xu -
Path planning of mobile robot by mixing experience with modified artificial potential field method2015 / H. Min, Y. Lin, S. Wang, F. Wu, X. Shen