Mechanical engineering topic list of research papers
-
An Effective Method for Solving the Induced Surface Current for Arbitrary Conducting Bodies at the Interior Resonance
Abstract The incorrect surface current may be obtained in the vicinity of the resonant frequencies when the method of moments is used to solve either the electric or magnetic field surface integral equation. An effective method is presented to...
2011 / Yu-fa Sun, Shan-jia Xu -
Conformity Analysis in the Measurement of Machined Metal Surfaces with Optoelectronic Profilometer
Abstract The objective of this work is to analyse the conformity of the roughness parameters measured with an optoelectronic profilometer in order to make equivalent the measurement results with those obtained with traditional contact devices. The...
2013 / E. Cuesta, B.J. Álvarez, M. García-Diéguez, D. González-Madruga, J.A. Rodríguez-Cortés -
To Analytically Estimate the 3D Position Deviation of a Holes Pattern due to Fixturing
Abstract This work considers how deviation on fixturing elements propagate on location tolerance of a holes’ pattern. The 3-2-1 locating principle has been adopted. The position of each locator is represented by a Gaussian probability density...
2013 / Antonio Armillotta, Giovanni Moroni, Wilma Polini -
Parking Choice Behavior Investigation: A Case Study at Beijing Lama Temple
Abstract Understanding parking choice behaviour is important in parking facility design and service evaluation. Lack of sufficient studies on parking choice behaviour investigation has been an issue in parking facility planning in China. Using six...
2013 / Xiaolong Ma, Xiaoduan Sun, Yulong He, Yixin Chen -
Water Hammer Assessment Techniques for Water Distribution Systems
Abstract The water hammer hazards are mainly in four aspects: the high water pressure bursting pipes, the vacuum flattening pipes and leading to water pollution, the cavitation damaging the pipes and pump impellers, as well as the transient force...
2014 / R. Wang, Z. Wang, X. Wang, H. Yang, J. Sun -
Combined and interactive effects of interference fit and preloads on composite joints
Abstract The combined and interactive effects of the bolt-hole fit conditions and the preloads of the fasteners on the load carrying capacity of single-lap composite-to-titanium bolted joints have been investigated both experimentally and...
2014 / Longquan Liu, Junqi Zhang, Kunkun Chen, Hai Wang -
Unbalance Response Analysis and Experimental Validation of an Ultra High Speed Motor-Generator for Microturbine Generators Considering Balancing2014 / Do-Kwan Hong, Dae-Suk Joo, Byung-Chul Woo, Dae-Hyun Koo, Chan-Woo Ahn
-
Modelling Complex Production Processes in Aerospace Industry based on Dimensional Analysis
Abstract This paper looks at the application of the principals of dimensional analysis to identify relations between key parameters of the production system in order to construct a process model that can quantitatively describe the influence of...
2013 / S.N. Grigoriev, A.A. Kutin, M.V. Turkin -
Delay Analysis of Stop Sign Intersection and Yield Sign Intersection based on VISSIM
Abstract Travel efficiency and traffic safety of unsignalized intersections are two main objectives considered in traffic management and control. Stop sign and yield sign are the most common traffic signs to display the right of the way for all...
2013 / Meiping Yun, Jing Ji -
An Adaptive Pedestrians Crossing Signal Control System for Intersection
Abstract In order to reduce the effect on vehicles in the major road and shorten the waiting time of pedestrians, an adaptive pedestrians crossing signal control system was designed in this paper. The system was composed of capturing units of video...
2013 / Mei Xiao, Lei Zhang, Yiming Hou, Song Chuan -
Numerical Simulation for the Unsteady MHD Flow and Heat Transfer of Couple Stress Fluid over a Rotating Disk2014 / Najeeb Alam Khan, Shahnila Aziz, Nadeem Alam Khan
-
Design of Friction Stir Welding Tool for Avoiding Root Flaws2013 / Shude Ji, Jingwei Xing, Yumei Yue, Yinan Ma, Liguo Zhang, et al.
-
Analysis and Comparison of Friction Stir Welding and Laser Assisted Friction Stir Welding of Aluminum Alloy2013 / Sabina Campanelli, Giuseppe Casalino, Caterina Casavola, Vincenzo Moramarco
-
Multi-Objective Thermo-Economic Optimization Strategy for ORCs Applied to Subcritical and Transcritical Cycles for Waste Heat Recovery2015 / Steven Lecompte, Sanne Lemmens, Henk Huisseune, Martijn van den Broek, Michel De Paepe
-
The Control of Tendon-Driven Dexterous Hands with Joint Simulation2014 / Jinbao Chen, Dong Han
-
Transmission electron microscopy study of semi-polar gallium nitride layer grown by hydride-chloride vapour-phase epitaxy on SiC/(001)Si heterostructure2013 / L M Sorokin, A E Kalmykov, A V Myasoedov, V N Bessolov, A V Osipov, et al.
-
Influence of Prewhirl Regulation by Inlet Guide Vanes on Cavitation Performance of a Centrifugal Pump2014 / Lei Tan, Baoshan Zhu, Shuliang Cao, Yuchuan Wang, Binbin Wang
-
Transient simulation of regression rate on thrust regulation process in hybrid rocket motor
Abstract The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–solid coupling is...
2014 / Hui Tian, Yijie Li, Peng Zeng -
Numerical study on flow fields and aerodynamics of tilt rotor aircraft in conversion mode based on embedded grid and actuator model
Abstract A method combining rotor actuator disk model and embedded grid technique is presented in this paper, aimed at predicting the flow fields and aerodynamic characteristics of tilt rotor aircraft in conversion mode more efficiently and...
2014 / Ying Zhang, Liang Ye, Shuo Yang -
Premixed Hydrogen/air Flame in Ceramic Granular Bed
Abstract This study investigates the characteristics of a lean premixed hydrogen/air flame in a ceramic granular bed (CGB) by conducting experimental measurements and numerical simulations. The experimental results show that the operating range...
2015 / S.I. Yang, S.C. Lin