Mechanical engineering topic list of research papers
-
Characterization of the Transient Response of Coupled Optimization in Multidisciplinary Design2013 / Erich Devendorf, Kemper Lewis
-
Experimental Investigation on an Absorption Refrigerator Driven by Solar Cells2013 / Zi-Jie Chien, Hung-Pin Cho, Ching-Song Jwo, Chao-Chun Chien, Sih-Li Chen, et al.
-
Heat and Mass Transfer in Reduction Zone of Sponge Iron Reactor2011 / Bayu Alamsari, Shuichi Torii, Azis Trianto, Yazid Bindar
-
Effectiveness of resilient wheels in reducing noise and vibrations2011 / B. Suarez, J. A. Chover, P. Rodriguez, F. J. Gonzalez
-
Effect of Reynolds and Prandtl Numbers on Mixed Convection in an Obstructed Vented Cavity2011 / M. M. Rahman, M. M. Billah, M. A. Alim
-
Analysis of Tire Contact Parameters Using Visual Processing2010 / Valentin Ivanov
-
Multidisciplinary Integrated Framework for the Optimal Design of a Jet Aircraft Wing2012 / Laura Mainini, Paolo Maggiore
-
Mixed Signature: An Invariant Descriptor for 3D Motion Trajectory Perception and Recognition2011 / Jianyu Yang, Y. F. Li, Keyi Wang, Yuan Wu, Giuseppe Altieri, et al.
-
Study of a Fuel Supply Pump with a Piezoelectric Effect for Microdirect Alcohol Fuel Cells2011 / Hsiao-Kang Ma, Jyun-Sheng Wang, Wei-Yang Cheng, Shin-Han Huang
-
Improved Quantum-Inspired Evolutionary Algorithm for Engineering Design Optimization2012 / Jinn-Tsong Tsai, Jyh-Horng Chou, Wen-Hsien Ho
-
Oscillatory Singularity Behaviors Near Interface Crack Tip for Mode II of Orthotropic Bimaterial2013 / Xiaomei Yang, Weiyang Yang, Junlin Li, Xuexia Zhang
-
Comparison of Engine Simulation Software for Development of Control System2013 / KinYip Chan, Andrzej Ordys, Konstantin Volkov, Olga Duran
-
Mechanics of Static Slip and Energy Dissipation in Sandwich Structures: Case of Homogeneous Elastic Beams in Transverse Magnetic Fields2012 / Charles A. Osheku
-
Dynamic Characteristics of Rotating Stall in Mixed Flow Pump2013 / Xiaojun Li, Shouqi Yuan, Zhongyong Pan, Yi Li, Wei Liu
-
Investigation of the Skive Hobbing Process by Applying a Dexel-based Cutting Simulation
Abstract In this paper, a novel approach for cutting simulation of skive hobbing is presented. Skive hobbing is a process applied for finishing of already hardened gears. The process is characterized by varying tool engagements and very small chip...
2015 / V. Böß, B. Denkena, S. Henning -
Elastohydrodynamic lubrication of hypoid gear pairs at high loads2012 / M. Mohammadpour, S. Theodossiades, H. Rahnejat
-
Supporting and evaluation systems of low carbon transport: Study on theory and practice2016 / Y. Huang, X. Hu, D. Zhang, X. Fang, X. Li
-
Effects of mesh resolution on hypersonic heating prediction
Abstract Aeroheating prediction is a challenging and critical problem for the design and optimization of hypersonic vehicles. One challenge is that the solution of the Navier-Stokes equations strongly depends on the computational mesh. In this...
2011 / Quanhua Sun, Huiyu Zhu, Gang Wang, Jing Fan -
Study on the Development of an Optimal Heat Supply Control Algorithm for Group Energy Apartment Buildings According to the Variation of Outdoor Air Temperature2012 / Jae-Ki Byun, Young-Don Choi, Jong-Keun Shin, Myung-Ho Park, Dong-Kurl Kwak
-
Parametric analysis of air–water heat recovery concept applied to HVAC systems: Effect of mass flow rates
Abstract In the last three decades, the world has experienced enormous increases in energy and fuel consumption as a consequence of the economic and population growth. This causes renewable energy and energy recovery to become a requirement in...
2015 / Mohamad Ramadan, Mostafa Gad El Rab, Mahmoud Khaled