Mechanical engineering topic list of research papers
-
Application of CFD technique for modelling of the thermoacoustic engine2012 / Sebastian Rulik, Leszek Remiorz, Sławomir Dykas
-
Nanocrystalline Ni-Co Alloy Synthesis by High Speed Electrodeposition2013 / Jamaliah Idris, Chukwuekezie Christian, Eyu Gaius
-
Sliding Mode Control for Trajectory Tracking of Intelligent Vehicle
Abstract The intelligent vehicle is a complex non-linear system of various machines, sensors and computers, of which the controller design for trajectory tracking is one of the key techniques for intelligent vehicles. For the high qualities of...
2012 / Jun Yang, Rong Ma, Yanrong Zhang, Chengzhi Zhao -
External Sensor-Less Tool Contact Detection by Cutting Force Observer
Abstract Precise tool length measurement and work coordinate setup is technically a difficult operation which generally requires a manual adjustment and takes long time. Contact of cutting edge of a micro tool is conventionally detected by laser,...
2012 / Y. Kakinuma, T. Kamigochi -
A Method of Removing ISAR Image Stripe Noise Based on the Target Axis and the Energy Band Analysis
Abstract ISAR image after image forming are often mixed with various stripe noise to affect the image quality. In this paper, we propose a method based on the target axis and the target energy band analysis of ISAR, combined with curve fitting to...
2012 / Yang Yuqi, Gao Xiaoguang, Feng Xiaoyi, Fan Jianping -
Multiple Nonholonomic Wheeled Mobile Robots Trajectory Tracking While Maintaining Time-Varying Formation via Synchronous Controller
Abstract A new synchronization control method is developed for multiple nonholonomic wheeled mobile robot path tracking while maintaining time-varying formations. Every robot is controlled to track its desired path while its movement is synchronized ...
2012 / Ibrahim M.H. Sanhoury, Shamsudin H.M. Amin, Abdul Rashid Husain -
LCA of Scrap CRT Display at Various Scenarios of Treatment
Abstract With the development of the science, technology and economy, electronic products became the important necessary products in daily life. Due to the large usage of electronic products, generation of the e-waste became more and more. The...
2012 / Ruxuan Niu, Zhishi Wang, Qingbin Song, Jinhui Li -
Empirical assessment of a RGB-D sensor on motion capture and action recognition for construction worker monitoring2013 / SangUk Han, Madhav Achar, SangHyun Lee, Feniosky Peña-Mora
-
Study on Simulation Modeling and Approximate Synchronous Computation Technology for the Active Structural Stiffness Design
Abstract In the past, structure design mainly adopted strength criterion. At the same time, many problems occurred due to structural stiffness deficiency. In order to resolve many practical problems resulted from structural stiffness in aircraft...
2012 / Xia Shenglai, He Jingwu, Chu Hongyu, Yang Xuan -
Tracing and Visualizing Variation of Chatter for In-Process Identification of Preferred Spindle Speeds
Abstract An analyzer has been developed for the purpose of tracing and visualizing the time dependent variation of chatter in terms of the frequency and the magnitude, and of determining the spindle speed for real-time on-line chatter suppression. ...
2012 / Hiromitsu Morita, Toru Yamashita -
Design and analysis of a 2-degree-of-freedom flexure-based micro-motion stage2016 / Y. Du, T. Li, Y. Jiang, H. Wang
-
Implementing Two-lane Highway Simulation Modeling into CORSIM1
Abstract While urban areas and the corresponding traffic demand continue to grow, rural areas are experiencing significant growth as well. This growth is now resulting in congestion on facilities that previously did not have any. One area that is...
2011 / Jing Li, Scott S. Washburn -
A New Algorithm for Bearings-Only Parametric Trajectory Tracking
Abstract For the single sensor target tracking with bearings-only measurements, a novel trajectory invariable-information target tracking algorithm was proposed, and bearings-only target can be tracked by the parameter trajectory. For the measure...
2011 / Jinmang Liu, Zhonglin Wu, Jinlong Yang, Zhenxing Li -
The Application of Fuzzy Group Analytic Network Process to Selection of Best Maintenance Strategy- A Case Study in Mobarakeh Steel Company, Iran
Abstract In order to increase reliability and safety level with reasonable cost, it is vital for companies to select the appropriate maintenance strategy. The main objective of this paper is to assess different maintenance strategies (namely Total...
2012 / Arash Sadeghi, Roshanak Alborzi Manesh -
Lane Utilization Analysis of Shared Left-turn Lane Based on Saturation Flow Rate Modeling
Abstract Lane utilization analysis is an essential task in the planning and design stage of signalized intersections and arterials. This task becomes difficult to perform satisfactorily when shared permissive left-turn lane is present. It allows...
2012 / Peng Chen, Hideki Nakamura, Miho Asano -
An Improved Kernel K-Mean Cluster Method and Its Application in Fault Diagnosis of Roller Bearing2013 / Ling-Li Jiang, Yu-Xiang Cao, Hua-Kui Yin, Kong-Shu Deng
-
Improvement of EDM Properties of PCD with Electrode Vibrated by Ultrasonic Transducer
Abstract EDM machinability of PCD was investigated using a copper electrode giving ultrasonic vibrations. In this series of EDM experiments, three types of ultrasonic vibration modes were selected (axial vibration, flexural vibration and complex...
2013 / M. Iwai, S. Ninomiya, K. Suzuki -
Potential saving in energy using combined heat and power technology for drying agricultural products (banana slices)
Abstract The drying behavior of banana slices was studied in a combined heat and power dryer system at 4 engine load levels (25%, 50%, 75%, and 100%) and at three levels of drying product thickness (3, 5, and 7mm) with the constant airflow velocity...
2013 / Seyed Hashem Samadi, Barat Ghobadian, Gholamhassan Najafi, Ali Motevali -
Improvement of Baldwin–Lomax turbulence model for supersonic complex flows
Abstract Entropy represents the dissipation rate of energy. Through direct numerical simulation (DNS) of supersonic compression ramp flow, we find the value of entropy is monotonously decreasing along the wall-normal direction no matter in the...
2013 / Rui Zhao, Chao Yan, Jian Yu, Xinliang Li -
Realization of Micro-EDM under Ultra-Small Discharge Energy by Applying Ultrasonic Vibration to Machining Fluid
Abstract Although micro-EDM has its potential in micro tool and part manufacturing, the machining speed is quite low due to short -circuits and abnormal discharges, because of the difficult debris removal from the narrow gap -width. Especially, the...
2013 / T. Ichikawa, W. Natsu