Mechanical engineering topic list of research papers
-
Simulation-based Optimization of HOT Lane Tolls
Abstract This paper presents a real-time simulation-based control framework to determine dynamic toll rates in order to optimize an operator's objective, subject to various operational and contractual constraints, such as smooth toll rate changes...
2015 / Tomer Toledo, Omar Mansour, Jack Haddad -
A Comparative Study of Improved Dynamics of Single Link Flexible Revolute-Jointed Robotic Manipulator
Abstract In this work, shape optimization is carried out of a single link flexible revolute flexible manipulator to extremize two objective functions (static tip deflection and fundamental frequency) using sequential quadratic programming (SQP)...
2016 / S. Mahto, A.K. Gogoi, U.S. Dixit -
Optimized use of cooling holes to decrease the amount of thermal damage on a plastic gear tooth2016 / D. Koffi, A. Bravo, L. Toubal, F. Erchiqui
-
Fabrication of a Flexible Tactile Sensor with Micro-Pillar Array
Abstract The tactile sensors are primarily used to measure the contact area and normal pressure of contacting two solids. The common deficiencies of the current tactile sensors are flexibility, adaptation to contacting bodies, normal and lateral...
2015 / Bilsay Sümer, Ilker Murat Koc -
Bionic Research on Bird Feather for Drag Reduction2015 / B. Feng, D. Chen, J. Wang, X. Yang
-
Double-layer ramp-metering model for incident congestion on expressway
Abstract: In order to ensure stable traffic capacity and avoid incident congestion, a double-layer ramp metering model is proposed in this paper, based on coordination control theory, to predict and control the traffic flow at each on-ramp, when...
2015 / Yihu Wu, Dan Yu, Wei Yu, Tao Qin, Yifen Li -
Experiment of aerosol-release time for a novel automatic metered dose inhaler2016 / M. Zhang, S. Wang, Y.-C. Yang
-
Reliability analysis on the drive system of a gear-type oil pump with variable displacement2016 / X. Wang, X. Liu, Y. Wang, X. Liu, H. Guo
-
Numerical investigation of boiling heat transfer on hydrocarbon mixture refrigerant in vertical rectangular minichannel2016 / H. Li, Y. Liu
-
TEA CO2 laser machining of CFRP composite2016 / A. Salama, L. Li, P. Mativenga, D. Whitehead
-
Investigation on Harmonic Generation of Submerged Elastic Plate Using Wave Flume Experiments2012 / M. Thayapraba, K. Murali, V. Subramanian
-
A Distributed Artificial Immune Network for Optimizing Tracer Kinetic Models with MATLAB Distributed Computing Engine2013 / Rui Lu, Li Liu, Lijun Shen
-
Numerical and experimental research of flow and sound fields in an axial-flow check valve and its optimization2015 / J. Yu, S. Yu
-
A study on automotive drivetrain transient response to 'clutch abuse events2015 / P. Bingham, S. Theodossiades, T. Saunders, E. Grant, R. Daubney
-
Mesoscale finite element model for calculating deformations of laminate composite constructions2016 / J. Stadnicki, Z. Tokarz
-
Monitoring and Source Tracing of Machining Error Based on Built-in Sensor Signal
Abstract Online monitoring and source tracing of machining error is of great significance for ensuring machining quality and improving machining efficiency. For an open numerical controller, the built-in sensors signals can be captured through...
2016 / Xinping Xu, Tao Tao, Gedong Jiang, Xiaoyong Huang, Runqing Liu, et al. -
Numerical simulation of heat transfer and turbulent flow of water nanofluids copper oxide in rectangular microchannel with semi-attached rib2016 / O. A. Akbari, D. Toghraie, A. Karimipour
-
The research on wing sail of a land-yacht robot2015 / S. Xie, J. Chen, H. Li, J. Luo, H. Pu, et al.
-
Sine-modulated wavelength-independent full-range complex spectral optical coherence tomography with an ultra-broadband light source2015 / Q. Zhang, S. Zhong, J. Zhong
-
Experimental study on depth of paraffin wax over floating absorber plate in built-in storage solar water heater2015 / R. Sivakumar, V. Sivaramakrishnan, M. Vivekanandan