Mechanical engineering topic list of research papers
-
Pyrotechnic robot: Costructive design and command2013 / Staretu Ionel, Ionescu Marius
-
A Combined Experimental and Numerical Study of Laminar and Turbulent Non-piloted Oxy-fuel Jet Flames Using a Direct Comparison of the Rayleigh Signal2015 / Franziska Hunger, Meor F. Zulkifli, Benjamin A. O. Williams, Frank Beyrau, Christian Hasse
-
Dynamic Analysis and Control of the Clutch Filling Process in Clutch-to-Clutch Transmissions2014 / Wei Guo, Yanfang Liu, Jing Zhang, Xiangyang Xu
-
Energy Efficiency of Compressed Air Systems
Abstract Compressed Air (CA) systems have a significant impact on the energy consumption and efficiency of manufacturing systems. These may be composed of a single compressor or include several compressors that work together in a logical manner....
2014 / Smaeil Mousavi, Sami Kara, Bernard Kornfeld -
Combined Optimal Sizing and Control for a Hybrid Tracked Vehicle2012 / Yuan Zou, Fengchun Sun, Xiaosong Hu, Lino Guzzella, Huei Peng
-
The Design of Gas Drainage Holes? Opening Parameters Intelligent Measurement and Control System for Coal Mine
Abstract Drilling Project is a huge project in coal main. Now mine is still measured in the method of artificial construction and acceptance. It is difficult to ensure that construction can meet the design parameters. The hole depth of gas drainage...
2011 / Jie Lian -
Effectiveness of Traffic Sign Setting in Adjacent Tunnel Exit
Abstract When pre and post structural opening in adjacent tunnel groups are in close proximity, the effective setting of traffic sign in the tunnel exit may affect drivers’ vision and driving safety. This paper investigates the effectiveness of...
2013 / Yan Bin, Zhou Ji-biao, Wang Lu -
Uncertainties in Road Vehicle Suspensions
Abstract Road vehicles are subject to random excitation by the unevenness of the road. For a dynamical analysis, vehicle models of the vertical vibrations as well as guideway models of the road unevenness are required. The fundamental dynamics of...
2015 / Werner Schiehlen, Igor Iroz -
A Dynamic Optimization Strategy for the Operation of Large Scale Seawater Reverses Osmosis System2014 / Aipeng Jiang, Jian Wang, Wen Cheng, Changxin Xing, Shu Jiangzhou
-
Miniaturized load sensor using quartz crystal resonator constructed through microfabrication and bonding2014 / Yuichi Murozaki, Kousuke Nogawa, Fumihito Arai
-
Increasing Cutting Tool Life when Machining Inconel 718
Abstract Machining of Inconel 718 is still very problematic. During the machining the cutting edge is stressed by high temperature and pressure in a small area. So it is important to use fluids with high pressure and a very accurate and high quality ...
2014 / Miroslav Zetek, Ivana Česáková, Vojtěch Švarc -
A Novel Abandoned Object Detection System Based on Three-Dimensional Image Information2015 / Yiliang Zeng, Jinhui Lan, Bin Ran, Jing Gao, Jinlin Zou
-
A 1D/3D Methodology for the Prediction and Calibration of a High Performance Motorcycle SI Engine
Abstract Nowadays internal combustion engines development is widely supported by 1D and 3D codes. On the other hand, an extensive experimental activity at test bench involves increased development cost and time-to-market of a new engine. For this...
2015 / Teodosio Luigi, Attilio Roberto, Nonatelli Fabio -
Calculation Of The Brushless DC Motor Shaft Speed With Allowances For Incorrect Alignment Of Sensors2015 / Krzysztof Kolano
-
A review of entropy generation in microchannels2015 / M. M. Awad
-
Autonomous path planning solution for industrial robot manipulator using backpropagation algorithm2015 / P. Yuan, F. Su, Z. Shi, T. Wang, D. Chen
-
Progress of continuously rotating detonation engines
Abstract Continuously rotating detonation engine (CRDE) is a focus for concern in the field of aerospace propulsion. It has several advantages, including one-initiation, high thermal efficiency and simple structure. Due to these characteristics, it...
2015 / Rui Zhou, Dan Wu, Jianping Wang -
Scenarios in Multi-objective Optimisation of Process Parameters for Sustainable Machining
Abstract Sustainable machining needs to consider multiple objectives for fulfilling environmental and economic requirements. Pareto front usually employed to present multi-objective optimisation results. However, the Pareto fronts are difficult to...
2015 / Taoyuan Zhang, Oladele Owodunni, James Gao -
An overview of the plastic-hinge analysis of 3D steel frames2015 / Van-Long Hoang, Hung Nguyen Dang, Jean-Pierre Jaspart, Jean-François Demonceau
-
Two-Stage Turbocharging for the Downsizing of SI V-Engines
Abstract One of the most critical challenges for the specific power increase of turbocharged SI engines is the low end torque, limited by two aspects. First, the big size of the compressor necessary to deliver the maximum airflow does not allow high ...
2015 / Carlo Alberto Rinaldini, Sebastiano Breda, Stefano Fontanesi, Tommaso Savioli