Mechanical engineering topic list of research papers
-
Barrier Lyapunov Function-Based Sliding Mode Control for Guaranteed Tracking Performance of Robot Manipulator2013 / Seong Ik Han, Jeong Yun Cheong, Jang Myung Lee
-
Rough Set Theory Based Fuzzy TOPSIS on Serious Game Design Evaluation Framework2013 / Chung-Ho Su, Ken T.-K. Chen, Kuo-Kuang Fan
-
Fast Stiffness Matrix Calculation for Nonlinear Finite Element Method2014 / Emir Gülümser, Uğur Güdükbay, Sinan Filiz
-
Risk-Optimized Design of Production Systems by Use of GRAMOSA2014 / Michael Lütjen, Abderrahim Ait Alla
-
Strain Rate Dependent Deformation of a Polymer Matrix Composite with Different Microstructures Subjected to Off-Axis Loading2014 / Xiaojun Zhu, Xuefeng Chen, Zhi Zhai, Zhibo Yang, Xiang Li, et al.
-
Study on Mitigation Method of Solder Corrosion for Crystalline Silicon Photovoltaic Modules2014 / Ju-Hee Kim, Jongsung Park, Donghwan Kim, Nochang Park
-
Experimental and Numerical Studies on Tire Tread Block Friction Characteristics Based on a New Test Device2014 / J. Wu, Y. S. Wang, B. L. Su, Q. Liu
-
Mobile Robots Path Planning Using the Overall Conflict Resolution and Time Baseline Coordination2014 / Yong Ma, Hongwei Wang, Langxiong Gan, Min Guo, Liwen Huang, et al.
-
In-phase thermal–mechanical fatigue investigation on hollow single crystal turbine blades
Abstract Thermal–mechanical fatigue (TMF) is the primary cause of failure of nickel-based single crystal turbine blades. TMF experiments have been performed on the critical section which is subjected to the most serious damage and determined by...
2013 / Rongqiao Wang, Fulei Jing, Dianyin Hu -
Reliability equivalence factors of a system with mixture of n independent and non-identical lifetimes with delay time
Abstract Recently, [1,2] generalized the reliability equivalence technique to a system with mixed of two non-identical lifetimes with delay time. The aim of this study is to generalize reliability equivalence technique to apply it to a system of...
2013 / Abdelfattah Mustafa, Adel A. El-Faheem -
A Structured Mesh Euler and Interactive Boundary Layer Method for Wing/Body Configurations
Abstract To compute transonic flows over a complex 3D aircraft configuration, a viscous/inviscid interaction method is developed by coupling an integral boundary-layer solver with an Eluer solver in a “semi-inverse” manner. For the turbulent...
2008 / Li Jie, Zhou Zhou -
Adaptive Approximation-based Optimization of Composite Advanced Grid-stiffened Cylinder
Abstract An adaptive approximation-based optimization (AABO) procedure is developed for the optimum design of a composite advanced grid-stiffened (AGS) cylinder subject to post-buckling. The design taking account of post-buckling under ultimate load ...
2010 / Wu Hao, Yan Ying, Yan Wei, Liao Baohua -
Dual Drive Curve Tool Path Planning Method for 5-axis NC Machining of Sculptured Surfaces
Abstract The problem of finished surface being not first-order continuous commonly exists in machining sculptured surfaces with a torus cutter and some other types of cutters. To solve this problem, a dual drive curve tool path planning method is...
2010 / Xu Rufeng, Chen Zhitong, Chen Wuyi, Wu Xianzhen, Zhu Jianjun -
Studies on Suitability of Heat Exchangers for Solar Receivers-Experimental Simulation and Numerical Investigation
Abstract The development of efficient solar receivers for different types of solar collectors such as point focusing, line focusing and external towers have received major attention in solar thermal power conversion process. The point focusing or...
2014 / D.R. Rajendran, E. Ganapathy Sundaram, Jawahar P., R. Pachaiyappan, G. Naveenraj -
Numerical investigation of unsteady vortex breakdown past 80°/65° double-delta wing
Abstract An improved delayed detached eddy simulation (IDDES) method based on the k-ω-SST (shear stress transport) turbulence model was applied to predict the unsteady vortex breakdown past an 80°/65° double-delta wing (DDW), where the angles of...
2014 / Jian Liu, Haisheng Sun, Zhitao Liu, Zhixiang Xiao -
Experimental investigation of exhaust temperature and delivery ratio effect on emissions and performance of a gasoline–ethanol two-stroke engine
Abstract In this study, the effects of ethanol additives (5%, 10% and 15% in volume) on the performance and emissions (HCs, CO, CO2 and NOx) of a SI two stroke engine is investigated in different loads and speeds. Also, the effect of exhaust...
2014 / Mohsen Ghazikhani, Mohammad Hatami, Behrouz Safari, Davood Domiri Ganji -
Effects of Deposition Models on Deposition and Performance Deterioration in Axial Compressor Cascade
Abstract A new particle deposition model, namely partial deposition model, is developed in order to improve the accuracy of prediction to particle deposition. Concepts of critical velocity and critical angle are proposed and used to determine...
2011 / Hui-xia JIA, Guang XI, Li-min GAO, Shu-ping WEN -
Testing of Low-grade Heat Source Organic Rankine Cycle with Small Hot Vapor Reciprocating Engine
Abstract Investigating for recovering low-grade heat source (<100oC) by the expansion process of the small hot vapor reciprocating engine has never been studied yet. This research focuses on that one and the organic rankine cycle has been...
2015 / Wasun Darawun, Roongrojana Songprakorp, Veerapol Monyakul, Sirichai Thepa -
Innovative Drive Concept for Machining Robots
Abstract In this paper an innovative drive concept for robots to improve their machining capability is presented. As a test bed a two-axis robot is designed and equipped with torque motors with load-sided high resolution encoders in addition to...
2013 / B. Denkena, K. Litwinski, M. Schönherr -
Thermoeconomic Optimization of a Renewable Polygeneration System Serving a Small Isolated Community2015 / Francesco Calise, Massimo d'Accadia, Antonio Piacentino, Maria Vicidomini