Mechanical engineering topic list of research papers
-
Can a brace be used to control the frequencies of a plate?2013 / Patrick Dumond, Natalie Baddour
-
Research of Initiative Personnel Orientation and Rescue System in Mine based on Synchronous Signal Sensei Technology
Abstract According to shortcomings of short-distance signal recognition, low signal transmission reliability, high rate of leakage reading and single function that exist in current underground personnel orientation system, a new system based on...
2011 / Shen Bin, Qin Xian-li, Fu Ming-chao -
Technology Feasibility Evaluation of Grid-connected Distributed Generation Based on Cloud Model
Abstract According to the particularity of the grid-connected distributed generation, this paper established a comprehensive multi-level evaluation index system for technology feasibility of the grid-connected distributed generation. The analytic...
2012 / Dongxiao Niu, Leilei Fan -
Modeling of pneumatic muscle with shape memory alloy and braided sleeve2010 / Bin-Rui Wang, Ying-Lian Jin, Dong Wei
-
Hybrid Map-Based Navigation Method for Unmanned Ground Vehicle in Urban Scenario2013 / Yuwen Hu, Jianwei Gong, Yan Jiang, Lu Liu, Guangming Xiong, et al.
-
Effect of traffic information on the stability pedestrian flow*
Abstract Based on traffic information, an extended two-dimensional optimal velocity model is presented by incorporating velocity difference between two neighboring pedestrians. Linear stability conditions are obtained by theoretical analysis, and...
2012 / Xiaomei Zhao, Dongfan Xie, Haiou Li -
Music expression with a robot manipulator used as a bidirectional tangible interface2012 / Victor Zappi, Antonio Pistillo, Sylvain Calinon, Andrea Brogni, Darwin Caldwell
-
The Research of Heating Furnace with Heavy Oil Desander
Abstract Based on the domestic and foreign oil field used heating furance, the pipes and instruments are worn and jammed by the sand in the heavy oil. The incrustation are formed on pipes’ inner surface which can cause cross-sectional area to be...
2012 / Feng Ding, Ruan Chao, Liu Xuhui, Wang Peng, Zhang Hong -
Ecomomic Assessment of Chilled Water Thermal Storage and Conventional Air-Conditioning Systems
Abstract In Kuwait, electricity is becoming an increasingly essential element of modern life. This flexible energy is used for heating, cooling, appliances, TVs, computers and transportation. The demand for electricity is growing at an average of...
2012 / M.J. Sebzali, B. Ameer, H.J. Hussain -
Optimization and Analysis of Distributed Energy System with Energy Storage Device
Abstract Aiming at distributed energy system (DES) with energy storage device, the mathematical models of major equipments are established in this paper. With the objective functions of the daily minimum operation cost and the minimum equipment...
2011 / Haitao Yun, Weiyi Li -
Finishing process analysis between honing and hard hobbing in pinion gears applied to a steering system
Abstract Among the techniques used in surface finish machining of gears, the honing process has been highlighted due to high efficiency in the finishing of hardened gears and ease of adjusting the involutes profile and incident angle in the...
2012 / Sandro Pereira dos Santos, Lincoln Cardoso Brandão, Luis Henrique Gallicchio, Zilda de Castro Silveira -
A Study on Aerodynamic Drag of a Semi-trailer Truck
Abstract The primary objective of this study is to determine the aerodynamic impact of various fuel saving devices used in a commercial vehicle (i.e., semi-trailer truck). To measure the aerodynamic drag produced by the vehicle, a wind tunnel study...
2013 / Harun Chowdhury, Hazim Moria, Abdulkadir Ali, Iftekhar Khan, Firoz Alam, et al. -
Different Kinematic Path Following Controllers for a Wheeled Mobile Robot of (2,0) Type2013 / Joanna Płaskonka
-
A New Hybrid Gyroscope with Electrostatic Negative Stiffness Tuning2013 / Bo Yang, Yumei Guan, Shourong Wang, Qi Zou, Xian Chu, et al.
-
Convective Heat Transfer through Thick-Walled Pipe
Abstract In the present study, convective heat transfer phenomenon has been investigated experimentally as well as numerically in a thick-walled pipe for laminar flow as well turbulent flow. Steady laminar and turbulent flow of water with uniform...
2012 / Sunil Chandel, R.D. Misal, Yonas G. Beka -
Tool wear monitoring using neuro-fuzzy techniques: a comparative study in a turning process2010 / Agustin Gajate, Rodolfo Haber, Raul del Toro, Pastora Vega, Andres Bustillo
-
An Autonomous Positioning and Navigation System for Spherical Mobile Robot
Abstract In this paper, we provide an autonomous positioning and navigation system for spherical robot. Firstly, the working principle and advantages of the spherical robot in our laboratory are described particularly. Secondly, the autonomous...
2012 / Kang Hou, Hanxu Sun, Qingxuan Jia, Yanheng Zhang -
Numerical Investigation on the Reynolds Number Effects of Supercritical Airfoil
Abstract Supercritical airfoil has been widely applied to large aircrafts for sake of high aerodynamic efficiency. The aerodynamic characteristics of supercritical airfoil are rather sensitive to Reynolds number. Therefore, Reynolds number has great ...
2012 / Dawei Liu, Yuanjing Wang, Dehua Chen, Xin Peng, Xing Xu -
Optimization of Cutting Path for Minimizing Workpiece Displacement at the Cutting Point: Changing the Material Removal Process, Feed Direction, and Tool Orientation
Abstract The vibrations of a workpiece during machining shorten the tool life and deteriorate the surface roughness in cases where the workpieces have a low stiffness (as is the case with artificial hip joints). In this paper, we propose a method to ...
2013 / Yusuke Koike, Atsushi Matsubara, Iwao Yamaji -
Numerical Study on Shear Flow in Sliding Bearing with Partial Slip Surface
Abstract For revealing the effects of slip on such characteristics as friction force and load-bearing capacity of sliding bearing, shear flows of a Newtonian fluid with a varying partial slip surface were computed using finite volume method....
2012 / Q. Lin, Z. Wei, Y. Tang