Mechanical engineering topic list of research papers
-
Attitude Control of a Flexible Satellite by Using Robust Control Design Methods2013 / Reza Mohsenipour, Hossein Nemati, Mehrzad Nasirian, Abdolreza Kashani Nia
-
An iterative numerical method for determination of temperature-dependent friction coefficients in thermomechanical model analysis of cold bolt forging2013 / U. Ince, M. Güden
-
Thermomechanical analysis of an elastoplastic rough body in sliding contact with flat surface and the effect of adjacent contact asperity2015 / J. Huang, C. Gao, J. Chen, X. Lin, Z. Ren
-
The principle and physical models of novel jetting dispenser with giant magnetostrictive and a magnifier2015 / C. Zhou, J.H. Li, J.A. Duan, G.L. Deng
-
Modelling and Control of the Multi-stage Cable Pulley-driven Flexible-joint Robot2014 / Phongsaen Pitakwatchara
-
Axis Position Dependent Dynamics of Multi-axis Milling Machines
Abstract Numerous analytical methods are available to predict the stability of milling processes. Most of these methods base on the assumption, that the dynamics of the machine tool are time invariant. This assumption seems to be valid in many...
2015 / C. Brecher, H. Altstädter, M. Daniels -
Influence of injection timing on DI diesel engine characteristics fueled with waste transformer oil
Abstract This research work targets on the effective utilization of WTO (waste transformer oil) in a diesel engine, which would rather reduce environmental problems caused by disposing of it in the open land. The waste transformer oil was compared...
2015 / S. Prasanna Raj Yadav, C.G. Saravanan, M. Kannan -
Geometry, Vibration Frequencies, Normal Coordinates and IR Absorption Intensities of [6]-Radialene2015 / Rehab M. Kubba, S. H. Rida, A. H. Hanoon
-
Design and analysis of automotive carbon fiber composite bumper beam based on finite element analysis2015 / T. Wang, Y. Li
-
Improvement of hydro-turbine draft tube efficiency using vortex generator2015 / X. Tian, H. Pan, S. Hong, Y. Zheng
-
Use of Multi-scale Approach for Vehicle Weight Reduction Study
Abstract This paper presents the use of the multi-scale approach developed by Nexter, to study the weight reduction of military armored vehicles. The fatigue design of such mechanical system is often complex due to the gap between the scale of the...
2014 / Romain Paquet, David Lebaillif, Eric Petitpas -
A Vibration-Based Strategy for Health Monitoring of Offshore Pipelines’ Girth-Welds2014 / Pejman Razi, Farid Taheri
-
Method Development of the Vibroacoustic Characteristics Calculation of the Gas Distribution Stations Elements
Abstract Pressure-reducing devices such as protective valves, control valves and chokes can create high levels of high-frequency acoustic waves at the outlet of the valve. These acoustic waves are propagated along the pipe, thereby generating...
2015 / Aleksandr A. Igolkin, Luiza F. Musaakhunova, Konstantin Yu. Shabanov -
Homogenized Finite Element Analysis on Effective Elastoplastic Mechanical Behaviors of Composite with Imperfect Interfaces2014 / Wu-Gui Jiang, Ren-Zhi Zhong, Qing Qin, Yong-Gang Tong
-
Effects of Direct Fuel Injection Strategies on Cycle-by-Cycle Variability in a Gasoline Homogeneous Charge Compression Ignition Engine: Sample Entropy Analysis2015 / Jacek Hunicz, Alejandro Medina, Grzegorz Litak, Pedro Curto-Risso, Lev Guzmán-Vargas
-
Performance Degradation Assessment of Rolling Element Bearings Based on an Index Combining SVD and Information Exergy2014 / Bin Zhang, Lijun Zhang, Jinwu Xu, Pingfeng Wang
-
Airworthiness Compliance Verification Method Based on Simulation of Complex System
Abstract A study is conducted on a new airworthiness compliance verification method based on pilot-aircraft-environment complex system simulation. Verification scenarios are established by “block diagram” method based on airworthiness criteria. A...
2012 / Haojun XU, Dongliang LIU, Yuan XUE, Li ZHOU, Guilong MIN -
Numerical Simulation of Premixed Methane-air Flame Propagating Parameters in Square Tube with Different Solid Obstacles
Abstract Based on the basic conservation equations, k − ɛ turbulence model, Zimont premixed combustion model and SIMPLE algorithm, the premixed methane-air flame propagating velocity and its pressure were numerical simulated in a half open square...
2013 / Quan Wang, Honghao Ma, Zhaowu Shen, Ziru Guo -
Flow Modeling in Various Cylindrical Surfaces
Abstract The proper and clear understanding of aerodynamics on different bodies such as aeroplanes, ships, automobiles, turbines and propeller's blades, tall towers, hydraulic structures, buildings etc. are of great importance in technology and...
2015 / Monalisa Mallick, A. Kumar, Anta Murmu -
Aerodynamic Design Methodology for Blended Wing Body Transport
Abstract This paper puts forward a design idea for blended wing body (BWB). The idea is described as that cruise point, maximum lift to drag point and pitch trim point are in the same flight attitude. According to this design idea, design objectives ...
2012 / Peifeng LI, Binqian ZHANG, Yingchun CHEN, Changsheng YUAN, Yu LIN