Mechanical engineering topic list of research papers
-
Thermodynamic Characteristic Study of a High-temperature Flow-rate Control Valve for Fuel Supply of Scramjet Engines
Abstract Thermodynamic characteristics are of great importance for the performance of a high-temperature flow-rate control valve, as high-temperature environment may bring problems, such as blocking of spool and increasing of leakage, to the valve....
2012 / Wen ZENG, Zhizhong TONG, Songjing LI, Hongzhou LI, Liang ZHANG -
Experimental and modeling study on effects of N2 and CO2 on ignition characteristics of methane/air mixture
Abstract The ignition delay times of methane/air mixture diluted by N2 and CO2 were experimentally measured in a chemical shock tube. The experiments were performed over the temperature range of 1300–2100K, pressure range of 0.1–1.0MPa, equivalence...
2014 / Wen Zeng, Hongan Ma, Yuntao Liang, Erjiang Hu -
Analysis and Design of Highway Monitoring System Based on MAS
Abstract The highway monitoring system is an open, intelligent, distributed complex information processing system. Analysis of the agent (Agent), Multi-Agent System (MAS) and Agent-oriented software design (AOP), the framework of the MAS- based...
2012 / Wang Qi, Mu Wenping -
Improvement on the Modeling of Rate-Dependent Plasticity and Cyclic Hardening by Bodner-Partom Model
Abstract An additional isotropic internal variable is utilized to extend the Bodner Partom unified viscoplastic constitutive model(original B-P) to improve the modeling of rate dependent plasticity and cyclic hardening behaviors of metals. The...
2011 / Duo-qi SHI, Xiao-guang YANG, Yan-rong WANG -
Adaptive Multi-scale Edge Detection Based on Region Energy
Abstract An adaptive multiscale edge detection method based on region energy analysis is presented here. Region energy distributions of both sides in different edge directions are studied. Based on the analysis and on the ratio between region energy ...
2011 / Ze-tao JIANG, Rong-chun ZHAO -
Multi-objective Optimization Design of Wing Structure with the Model Management Framework
Abstract Evolutionary algorithm is time-consuming because of the large number of evolutions and much times of finite element analysis, when it is used to optimize the wing structure of a certain high attitude long endurance unmanned aviation...
2011 / Wei-gang AN, Wei-ji LI, Zhong-qiu GOU -
Study on the Machining Distortion of Thin-walled Part Caused by Redistribution of Residual Stress
Abstract In order to reduce the weight of airplane and increase its mechanical behaviors, more and more large integrated parts are applied in modern aviation industry. When machining thin-walled aeroplane parts, more than 90% of the materials would...
2011 / Zhao-jun WANG, Wu-yi CHEN, Yi-du ZHANG, Zhi-tong CHEN, Qiang LIU -
Solar Heating and Cooling System with Absorption Chiller and Latent Heat Storage – A Research Project Summary
Abstract A reliable solar thermal cooling and heating system with high solar fraction and seasonal energy efficiency ratio (SEER) is preferable. By now, bulky sensible buffer tanks are used to improve the solar fraction for heating purposes. During...
2014 / Martin Helm, Kilian Hagel, Werner Pfeffer, Stefan Hiebler, Christian Schweigler -
Effect of graph generation on slope stability analysis based on graph theory
Abstract Limit equilibrium method (LEM) and strength reduction method (SRM) are the most widely used methods for slope stability analysis. However, it can be noted that they both have some limitations in practical application. In the LEM, the...
2014 / Enpu Li, Xiaoying Zhuang, Wenbo Zheng, Yongchang Cai -
Walking Robot Locomotion System Conception2014 / D. Ignatova, E. Abadjieva, V. Abadjiev, Al. Vatzkitchev
-
Planetary gear dynamic response to mesh parametric excitation2013 / Batinic Vojislav
-
Cycle Life of Commercial Lithium-Ion Batteries with Lithium Titanium Oxide Anodes in Electric Vehicles2014 / Xuebing Han, Minggao Ouyang, Languang Lu, Jianqiu Li
-
Exergy Analysis of a Ground-Coupled Heat Pump Heating System with Different Terminals2015 / Xiao Chen, Xiaoli Hao
-
A numerical study: liquid sloshing dynamics in a tank due to uncoupled sway, heave and roll ship motions2014 / Nasar Thuvanismail, Sannasiraj Sannasi, Sundar Vallam
-
FRP-RC Beam in Shear: Mechanical Model and Assessment Procedure for Pseudo-Ductile Behavior2014 / Floriana Petrone, Giorgio Monti
-
Determination of Tissue Thermal Conductivity by Measuring and Modeling Temperature Rise Induced in Tissue by Pulsed Focused Ultrasound2014 / Tamara Kujawska, Wojciech Secomski, Eleonora Kruglenko, Kazimierz Krawczyk, Andrzej Nowicki
-
Investigation on the Kinetics of Iron Ore Fines Reduction by CO in a Micro-fluidized Bed
Abstract Kinetics of Brazilian iron ore fines reduction was investigated in a micro fluidized bed, a newly developed kinetics analyzer for gas-solid reactions, where the effects of external and internal diffusion were significantly reduced by...
2015 / Hongsheng Chen, Zhong Zheng, Wanyuan Shi -
Simultaneous Multi-pipe Failure Impact on Reliability of Water Distribution Systems
Abstract Hydraulic reliability assessment of a water distribution system (WDS) can be performed at different states considering various combinations of pipe failures. Current reliability techniques are mostly restricted to lower sates of reliability ...
2014 / A. Gheisi, G. Naser -
Evaluating the Design for Additive Manufacturing: A Process Planning Perspective
Abstract The emergence of Additive Manufacturing (AM) has greatly liberated the designers’ hands, since the usual design constraints in machining or other traditional processing technologies partially or even totally disappeared in AM and it seems...
2014 / Yicha Zhang, Alain Bernard, Ravi Kumar Gupta, Ramy Harik -
A Comprehensive Mathematical Programming Model for Minimizing Costs in A Multiple-Item Reverse Supply Chain with Sensitivity Analysis2014 / Hoda Mahmoudi, Hamed Fazlollahtabar