Mechanical engineering topic list of research papers
-
Interferometric Surface Relief Measurements with Subnano/Picometer Height Resolution2017 / Evgeny Sysoev, Sergey Kosolobov, Rodion Kulikov, Alexander Latyshev, Sergey Sitnikov, et al.
-
Development of a new conflict-based safety metric for freeway exit ramps2017 / Tao Wang, Chen Wang, Zhendong Qian
-
Analysis of traffic state variation patterns for urban road network based on spectral clustering2017 / Senyan Yang, Jianping Wu, Geqi Qi, Kun Tian
-
Mechanical performance analysis of hollow cylindrical roller bearing of cone bit by FEM
Abstract Bearings are key components of cone bit, thus its rapid failure is a major cause of leading to lower life of the bit. To improve the bearing performance and prolong working life, contact mechanics of hollow cylindrical roller bearing of...
2015 / Chuanjun Han, Cheng Yu, Ying Li, Jiawei Yan, Jie Zhang -
Research on impact behaviour and silicon insert fracture phenomenon in microinjection moulding2015 / Zheng Xu, Zhi-bin Lv, Lin-gang Wang, Kai-yu Jiang, Zhi Ji, et al.
-
Optimization of molten carbonate fuel cell (MCFC) and homogeneous charge compression ignition (HCCI) engine hybrid system for distributed power generation
Abstract In a previous study, a new hybrid system of molten carbonate fuel cell (MCFC) and homogeneous charge compression ignition (HCCI) engine was developed, where the HCCI engine replaces the catalytic burner and produces additional power by...
2013 / Seonyeob Kim, Ji Young Jung, Han Ho Song, Seung Jin Song, Kook Young Ahn, et al. -
Sparse motion bases selection for human motion denoising
Abstract Human motion denoising is an indispensable step of data preprocessing for many motion data based applications. In this paper, we propose a data-driven based human motion denoising method that sparsely selects the most correlated subset of...
2014 / Jun Xiao, Yinfu Feng, Mingming Ji, Xiaosong Yang, Jian J. Zhang, et al. -
Timetable optimization for single bus line based on hybrid vehicle size model
Abstract This study proposes a flexible timetable optimization method based on hybrid vehicle size model to tackle the bus demand fluctuations in transit operation. Three different models for hybrid vehicle, large vehicle and small vehicle are built ...
2015 / Daniel(Jian) Sun, Ya Xu, Zhong-Ren Peng -
Bi-directional series-parallel elastic actuator and overlap of the actuation layers2016 / Raphaël Furnémont, Glenn Mathijssen, Tom Verstraten, Dirk Lefeber, Bram Vanderborght
-
A hierarchical updating method for finite element model of airbag buffer system under landing impact
Abstract In this paper, we propose an impact finite element (FE) model for an airbag landing buffer system. First, an impact FE model has been formulated for a typical airbag landing buffer system. We use the independence of the structure FE model...
2015 / Huan He, Zhe Chen, Cheng He, Lei Ni, Guoping Chen -
Generating Enhanced Intersection Maps for Lane Level Vehicle Positioning based Applications
Abstract Electronic map database is of great significance for precise vehicle positioning in several location-based safety applications, especially at the lane level. In order to provide essential reference information to assist lane-level vehicle...
2013 / Jiang Liu, Baigen Cai, Yunpeng Wang, Jian Wang -
Study on the motion control of snake-like robots on land and in water
Summary In order to fully use the advantage of legless body and rhythmic gaits to realize the inspection task, the snake-like robots and dynamic simulators are developed with components available online and open source software. The Serpenoid Curve...
2015 / Zhenli Lu, Dayu Feng, Yafei Xie, Huigang Xu, Limin Mao, et al. -
Enhancing vehicle cornering limit through sideslip and yaw rate control
Abstract Fully electric vehicles with individually controlled drivetrains can provide a high degree of drivability and vehicle safety, all while increasing the cornering limit and the ‘fun-to-drive’ aspect. This paper investigates a new approach on...
2015 / Qian Lu, Pierangelo Gentile, Antonio Tota, Aldo Sorniotti, Patrick Gruber, et al. -
Analytical gradient-based optimization of offshore wind turbine substructures under fatigue and extreme loads
Abstract Design optimization of offshore wind turbine support structures is an expensive task due to the highly-constrained, non-convex and non-linear nature of the design problem. A good depth of detail in the problem formulation can give useful...
2016 / Kok-Hon Chew, Kang Tai, E.Y.K. Ng, Michael Muskulus -
Experimental and numerical investigation of ion signals in boosted HCCI combustion using cesium and potassium acetate additives
Abstract A sparkplug ion sensor can be used to measure the ion current in a homogeneous charge compression ignition (HCCI) engine, providing insight into the ion chemistry inside the cylinders during combustion. HCCI engines typically operate at...
2015 / J. Hunter Mack, Ryan H. Butt, Yulin Chen, Jyh-Yuan Chen, Robert W. Dibble -
Design and testing of a shape memory alloy buoyancy engine for unmanned underwater vehicles2015 / Alex J Angilella, Farhan S Gandhi, Timothy F Miller
-
Motion synchronization in a dual redundant HA/EHA system by using a hybrid integrated intelligent control design
Abstract This paper presents an integrated fuzzy controller design approach to synchronize a dissimilar redundant actuation system of a hydraulic actuator (HA) and an electro-hydrostatic actuator (EHA) with system uncertainties and disturbances. The ...
2015 / Waheed Ur Rehman, Shaoping Wang, Xingjian Wang, Lei Fan, Kamran Ali Shah -
Modeling of reliability and performance assessment of a dissimilar redundancy actuation system with failure monitoring
Abstract Actuation system is a vital system in an aircraft, providing the force necessary to move flight control surfaces. The system has a significant influence on the overall aircraft performance and its safety. In order to further increase...
2015 / Shaoping Wang, Xiaoyu Cui, Jian Shi, Mileta M. Tomovic, Zongxia Jiao -
Dynamic simulator and model predictive control of an integrated solar combined cycle plant
Abstract This paper presents the design and evaluation of a dynamic simulator for an ISCC (integrated solar combined cycle) plant. The design of the simulator is based on the phenomenological equations for both a combined cycle plant and a solar...
2016 / Carolina V. Ponce, Doris Sáez, Carlos Bordons, Alfredo Núñez -
Experimental analysis on filter press and energy consumption performance of diaphragm press drying device in chemical post-processing integrated equipment
Abstract Higher efficiency, lower energy consumption and less pollution are become more and more important in chemical engineering. Post-process is one of the key parts for producing chemical productions. Thus, we develop a novel device, Chemical...
2016 / Yin-Fa Zhu, Jin-Yuan Qian, Qian-Kun Zhang, Ji-Yong Kuang, Xiao-Fei Gao, et al.