Mechanical engineering topic list of research papers
-
Forming of Hollow Shaft Forging From Titanium Alloy Ti6Al4V by Means of Rotary Compression2015 / J. Tomczak, Z. Pater, T. Bulzak
-
Homogeneous droplet nucleation modeled using the gradient theory combined with the PC-SAFT equation of state2013 / Barbora Planková, Jan Hrubý, Václav Vinš
-
Analysis of the Impact of Decreasing District Heating Supply Temperature on Combined Heat and Power Plant Operation2015 / Alona Bolonina, Genadijs Bolonins, Dagnija Blumberga
-
Analysis of Relation between Grinding Wheel Wear and Abrasive Grains Wear
Abstract The productivity of technological operation, accuracy, and surface finish depend on the patterns of tool wear and the state of its working surface. It was established that the prediction of the wear of tool is only possible based on...
2016 / Yu. Novoselov, S. Bratan, V. Bogutsky -
The Mathematical Modeling and Investigation of the Stress-Strain State of the Three-Layer Thermosensitive Hollow Cylinder2016 / Iryna Rakocha, Vasyl Popovych
-
Validation of smartphone gyroscopes for mobile biofeedback applications2016 / Anton Umek, Anton Kos
-
Solving a mathematical model integrating unequal-area facilities layout and part scheduling in a cellular manufacturing system by a genetic algorithm2016 / Ahmad Ebrahimi, Reza Kia, Alireza Rashidi Komijan
-
Effect of slip condition on vertical channel flow in the presence of radiation2016 / M. Guria
-
Thermoelastic Analysis of Functionally Graded Hollow Circular Disc2015 / Dávid Gönczi, Istvàn Ecsedi
-
E2Rebot: A robotic platform for upper limb rehabilitation in patients with neuromotor disability2016 / J. C. Fraile, J. Perez-Turiel, E. Baeyens, P. Vinas, R. Alonso, et al.
-
Additive Manufacturing and High Speed Machining -cost Comparison of short Lead Time Manufacturing Methods
Abstract Additive Manufacturing (AM) using Powder Bed Fusion (PBF) allows part with abstract shapes, that otherwise would need costly tooling, to be manufactured with short lead time. In this study AM build time simulations are used to predict...
2016 / Sebastian Hällgren, Lars Pejryd, Jens Ekengren -
Evaluation of the Dynamic Characteristics of Aircraft during Landing in Crosswinds2016 / Mareks Slihta, Irina Lazareva, Vladimirs Sestakovs
-
Research on tightness loss of belt conveyor's idlers and its impact on the temperature increase of the bearing assemblies
Abstract The temperature of idlers' bearing assemblies is the basic indicator of their technical condition. The main aim of this article is to present the impact of decreased tightness of the conveyor belts' idlers which results in the higher...
2016 / Andrzej Pytlik, Klaudiusz Trela -
Development of a waste heat recovery system onboard LNG carrier to meet IMO regulations
Abstract Problems resulting from gas emissions lead to increase the concern about safety and health issues with the demand to reduce the emissions from marine shipping. Marine power plants are considered as one of the greatest contributors in the...
2016 / Khaled Senary, Adel Tawfik, Elsayed Hegazy, Amr Ali -
Energy, Power and Heat Flow of the Cooling and Fluid Systems in a Cutting Machine Tool
Abstract Cooling is one of the main tasks of fluid systems in cutting machine tools. Cooling systems are essential for controlling the thermo-elastic properties of the whole machine structure. The paper describes an experimental investigation of a...
2016 / Juliane Weber, Jürgen Weber, Linart Shabi, Harald Lohse -
Multihops Fitting Approach for Node Localization in Underwater Wireless Sensor Networks2015 / Linfeng Liu, Jiagao Wu, Zhiwen Zhu
-
A multiresolution approach for damage detection in fiber-reinforced polymer pipe systems2016 / M. El-Gebeily, Y. Khulief, A. Ghneim
-
Vibration detection method for optical fibre pre-warning system2016 / Qu Hongquan, Pang Liping, Zheng Tong, Bi Fukun
-
Effects of wall suction/blowing on two-dimensional flow past a confined square cylinder2016 / Wei Zhang, Yanqun Jiang, Lang Li, Guoping Chen
-
Consensus-based sparse signal reconstruction algorithm for wireless sensor networks2016 / B. Peng, Z. Zhao, G. Han, J. Shen