Mechanical engineering topic list of research papers
-
Prediction of the aerodynamic behavior of a rounded corner square cylinder at zero incidence using ANN
Abstract The aerodynamic behavior of a square cylinder with rounded corner edges in steady flow regime in the range of Reynolds number (Re) 5–45; is predicted by Artificial Neural Network (ANN) using MATLAB. The ANN has trained by back propagation...
2016 / Prasenjit Dey, Abhijit Sarkar, Ajoy Kumar Das -
Perceptual Continuity and Naturalness of Expressive Strength in Singing Voices Based on Speech Morphing2007 / Tomoko Yonezawa, Noriko Suzuki, Shinji Abe, Kenji Mase, Kiyoshi Kogure
-
Research on collision-preventing decisions of oncoming vehicles2016 / H. Liu, L. Wang, H. Liu
-
Design of a microelectromechanical systems resonant electric field sensor with sensitivity robustness2015 / H. Liu, J.-q. Xu, F. Xiong, R.-l. Meng
-
Passive Control of Near-wall Turbulence By Means of Roughness Elements
Abstract The present work experimentally investigates the effect of roughness elements onto zero-pressure-gradient turbulent boundary layer. We use an array of spanwisely-aligned cylindrical roughness elements attached on the wall surface to...
2015 / Chong Pan, Jinjun Wang -
Deploying time investigation of automotive active hood lift mechanism with different design parameters of hinge part2016 / T.-H. Lee, G.-H. Yoon, S.-B. Choi
-
Analysis of High Speed Train Equipment Cabin Temperature Field Based on Numerical Simulation
Abstract In order to investigate the ventilation performance in the equipment cabin of a high-speed railway train, this paper uses computational fluid dynamics (CFD) method to simulate the air flow and temperature field in indoor and outdoor space...
2015 / Qiong Jia, Jianbin Zang, Deng Pan, Chunjing Xia, Jun Xu, et al. -
Numerical Simulations of Fast-start Motions of Fish
Abstract Fast-start swimming is a very special and important type of locomotion of fish. Basically, fast-star motion can be classified into two types: C-type and S-type. It is generally thought that the C-type fast-start is adopted by fish for...
2014 / Yu-Chiao Su, Tzuyin Wu -
Evaporation and dynamic characteristics of a high-speed droplet under transcritical conditions2016 / S. Yang, Y. Gao, C. Deng, B. Xu, F. Ji, et al.
-
Numerical study of heat transfer enhancement by rectangular winglet vortex generator pair in a channel2016 / Q. Zhang, L.-B. Wang
-
Optimization of the drying parameters for the short-form spray dryer producing powdered egg with 20% tapioca starch additive2015 / J. T. Masilungan-Manuel, M. C. E. Manuel, P. T. Lin, A. N. Soriano
-
A new method for ship inner shell optimization based on parametric technique2015 / Yan-Yun Yu, Yan Lin, Kai Li
-
Validation and Visualization of Decaying Vortex Flow in an Annulus
Abstract Swirling jets produced using inlet swirlers are often used to increase the heat or mass diffusion rates in heat exchangers or reactors, separation of smoke and dust suspended in the air in ventilation ducts etc. The aim of this work is to...
2015 / Baiman Chen, Kelvin Ho, Frank G.F. Qin, Runhua Jiang, Yousif A. Abakr, et al. -
A combinational efficient algorithm for elliptic eigenvalue problems2016 / H. Zhang, J. Cao
-
A Novel Approach to Enhance Performance of Multilayer Coated Carbide Insert in Hard Turning2016 / Suha K. Shihab, Zahid A. Khan, Arshad Noor Siddiquee, Noor Zaman Khan
-
Direct Monte Carlo simulation of nanoscale mixed gas bearings2015 / K. S. Myo, W. Zhou, K. L. Lee, S. Yu, W. Hua
-
Experiments and performances of strain-hardening fiber low cementitious composites2015 / C.-G. Cho, H.-J. Lim, B.-Y. Lee, Y. Choi
-
The wave energy scattering by interaction with the refracted breakwater and varying trench depth2015 / S.-D. Kim, K.-W. Jun, H.-J. Lee
-
Experimental evaluation of viscous damping coefficient in the fractional underdamped oscillator2016 / J. Escalante-Martinez, J. Gomez-Aguilar, C. Calderon-Ramon, L. Morales-Mendoza, I. Cruz-Orduna, et al.
-
The Method of Generating Large-span Rod Systems with the Manufacturer Defect and Assembly Sequence
Abstract Mathematical models of the method of generating large-span rod systems with the manufacturer defect and assembly sequence at construction process are offered in the article. The explanations and formulas used in the universal algorithm that ...
2015 / Alexey Bondarev, Anatoliy Yugov