Mechanical engineering topic list of research papers
-
Genetic algorithm for design optimization of multibody dynamics using differential-algebraic equation integrators2015 / J. Ding
-
Unified Singularity Modeling and Reconfiguration of 3rTPS Metamorphic Parallel Mechanisms with Parallel Constraint Screws2015 / Y. Zhuang, D. Gan
-
Application of image processing based on multiple filters in an alignment system2014 / Peiying Zeng, Baoqiang Zhu, De’an Liu, Jianqiang Zhu
-
The Effect of Positions of Vertical Glass Fins inside a Double Skin Façade Air Cavity as Acoustical Barriers and Ventilation Potentials
Abstract A number of studies state that natural ventilation strategies can contribute to improving indoor air quality (IAQ) and thermal comfort; however, noise annoyance by urban traffic noise transmission is a significant challenge that leads to...
2016 / Jeehwan Lee, Haider Mohamed, Jae D. Chang -
Proposal of a Design Method for Dismantling Products with Split-Lines
Abstract An important process for the reuse and recycling of end of life products is their disassembly. In general, manual disassembly is a labor intensive and costly process. Especially, removing fasteners takes time and cost. For solving this...
2015 / Yumi Shiraishi, Naoya Miyaji, Shinichi Fukushge, Yasushi Umeda -
Research on safety assessment method for bridge structure based on variable weight synthesis method
Summary Variable weight synthesis method is a safety assessment method which is using the varied weight principle, based on analytic hierarchy process and combining the theory of grey relevancy, it reduce influence that secondary cause is not...
2015 / Liu Cong -
A fuzzy recommendation system for daily water intake2016 / B. Dai, R.-C. Chen, S.-Z. Zhu, C.-Y. Huang
-
Numerical modeling of soot formation in a turbulent C2H4/air diffusion flame2016 / M. R. Busupally, A. De
-
OpenCV-Based Nanomanipulation Information Extraction and the Probe Operation in SEM2015 / D. Li, J. Song, D. Wang, W. Rong
-
Study on high-speed cutting parameters optimization of AlMn1Cu based on neural network and genetic algorithm2016 / Z. Wang, J. Yuan, Z. Yin, C. Li
-
Analytical Solution for Adiabatic Surface Temperature (AST)2016 / Michał Malendowski
-
Measuring reliability under epistemic uncertainty: Review on non-probabilistic reliability metrics
Abstract In this paper, a systematic review of non-probabilistic reliability metrics is conducted to assist the selection of appropriate reliability metrics to model the influence of epistemic uncertainty. Five frequently used non-probabilistic...
2016 / Rui Kang, Qingyuan Zhang, Zhiguo Zeng, Enrico Zio, Xiaoyang Li -
Motion Behavior of Nonmetallic Inclusions at the Interface of Steel and Slag. Part I: Model Development, Validation, and Preliminary Analysis2016 / Chao Liu, Shufeng Yang, Jingshe Li, Libin Zhu, Xiaogang Li
-
Lane Tracking with Omnidirectional Cameras: Algorithms and Evaluation2007 / Shinko Yuanhsien Cheng, Mohan Manubhai Trivedi
-
BBot, a hopping two-wheeled robot with active airborne control2016 / Huei Ee Yap, Shuji Hashimoto
-
Using Adaptive Tone Mapping to Enhance Edge-Preserving Color Image Automatically2010 / Kuo-Jui Hu, Min-Yao Lu, Je-Chuang Wang, Tao-I Hsu, Ting-Ting Chang
-
Torque-Controlled Adaptive Speed Control on a CNC Marble Saw Machine2015 / U. Simsir
-
Application of Taguchi Method to the Optimization of a-C:H Coatings Deposited Using Ion Beam Assisted Physical Vapor Deposition2015 / W. H. Kao, Y. L. Su, J. H. Horng, S. H. Yao, H. C. Huang
-
Optimal design of hydraulic excavator working device based on multiple surrogate models2016 / Q. Qiu, B. Li, P. Feng
-
Experimental and numerical investigation of heat transfer, temperature distribution, and louver efficiency on the dimpled louvers fin banks2015 / F. Sangtarash, H. Shokuhmand