Mechanical engineering topic list of research papers
-
Adsorption isotherms and Sips models of nitrogen, methane, ethane, and propane on commercial activated carbons and polyvinylidene chloride2016 / Nir Tzabar, H. J. M. ter Brake
-
HMI ASPECTS OF THE USABILITY OF INTERNET SERVICES WITH AN IN-CAR TERMINAL ON A DRIVING SIMULATOR
An experiment on the usability assessment of various control interfaces of an in-vehicle Internet browser, was carried out on the Renault driving simulator with a fictional web site that offers services such as: district map, route planning, electronic messaging,...
2014 / J-F. KAMP, J-F. FORZY, C. MARIN-LAMELLET, D. CAUSEUR -
Large amplitude free vibration of axially loaded beams resting on variable elastic foundation
Abstract In the present study, large amplitude free vibration of beams resting on variable elastic foundation is investigated. The Euler–Bernoulli hypothesis and the Winkler model have been applied for beam and elastic foundation, respectively. The...
2016 / Alborz Mirzabeigy, Reza Madoliat -
Dynamic modeling of double-helical gear with Timoshenko beam theory and experiment verification2016 / J. Dong, S. Wang, H. Lin, Y. Wang
-
Optimization on cooperative feed strategy for radial–axial ring rolling process of Inco718 alloy by RSM and FEM
Abstract During radial–axial ring rolling process, cooperative strategy of the radial–axial feed is critical for dimensional accuracy and thermo mechanical parameters distribution of the formed ring. In order to improve the comprehensive quality of...
2016 / Xinglin Zhu, Dong Liu, Yanhui Yang, Yang Hu, Yong Zheng -
Consistency of Calculation Results of Two Typical Vehicle Collision Models
Abstract In order to study consistency of calculation results of typical vehicle collision models based on the law of momentum conservation, the difference of coordinate systems of two typical models is analyzed. Consistency of two typical models is ...
2016 / Jian Zhang, Chao Liang, Shengwu Yu, Ruijun Liu, Jingui Gao -
Unsteady flow characteristic analysis of turbine based combined cycle (TBCC) inlet mode transition
Abstract A turbine based combined cycle (TBCC) propulsion system uses a turbine-based engine to accelerate the vehicle from takeoff to the mode transition flight condition, at which point, the propulsion system performs a “mode transition” from the...
2015 / Jun Liu, Huacheng Yuan, Guo Rongwei -
Hydro-Elastic Simulation of Stern Slamming and Whipping2010 / J. Oberhagemann, O. El Moctar, M. Holtmann, T. Schellin, V. Bertram, et al.
-
On the Numerical Study of Bubbly Wakes Generated by Ventilated Cavity using Population Balance Approach2010 / M. Xiang, S. C. P. Cheung, J. Y. Tu, W. H. Zhang
-
Computer-aided manufacturing for mass production of non-conventional shapes made of the alloying of a heterogeneous composite metallic glass matrix with nano-meter-sized elements2015 / S. A. Elmoselhy
-
VHCF Properties of A7075-T651 Al Alloy Depending on Shot Peening and Fatigue Testing Methods2015 / M.-S. Suh, C. H. Suh, S.-H. Nahm, C.-M. Suh
-
The comparative analysis of rocks’ resistance to forward-slanting disc cutters and traditionally installed disc cutters2015 / Zhao-Huang Zhang, Sun Fei, Meng Liang
-
Experimental Study on the Thermal Performance of Ventilation Wall with Cladding Panels in Hot and Humid Area
Abstract In this paper, we discussed the principle of thermal pressure ventilation, tested the ventilation wall in hot and humid region and obtained the hourly temperature on the outer wall surface and the calcium silicate board surface. The results ...
2015 / Zhihua Zhu, Xueli Jin, Qiong Li, Qinglin Meng -
Kinematic analysis of cable-driven parallel mechanisms based on minimum potential energy principle2015 / G. Liwen, X. Huayang, L. Zhihua
-
The Influence of Mixture Heating and EGR Delivery on SI Engine Efficiency at Part Load – Final Results2013 / Ľubomír Miklánek
-
Shock wave configurations and reflection hysteresis outside a planar Laval nozzle
Abstract When the pressure ratio increases from the perfectly expanded condition to the third limited condition in which a normal shock is located on the exit plane, shock wave configurations outside the nozzle can be further assorted as no shock...
2015 / Dan Wang, Yong Yu -
A multi-agent based scheduling algorithm for adaptive electric vehicles charging
Abstract This paper presents a decentralized scheduling algorithm for electric vehicles charging. The charging control model follows the architecture of a Multi-Agent System (MAS). The MAS consists of an Electric Vehicle (EV)/Distributed Generation...
2016 / Erotokritos Xydas, Charalampos Marmaras, Liana M. Cipcigan -
Experimental Investigation of Leading Edge Bluntness Effects on Hypersonic Tow-dimensional Inlet
Abstract The leading edge bluntness effects on inlet boundary layer transition had been studied based on a typical hypersonic two-dimensional inlet. Four leading edge radii(R=0.05mm, R =0.1mm, R =0.2mm, R =0.25mm) had been experimented in FD-07 wind ...
2015 / Zhang Hong-jun, Shen Qing -
Investigations of rheological properties of nitrided steels using thermodilatometric method with temperature modulation2016 / P. Myśliński, A. Gilewicz, R. Olik, K. Mydłowska, Ł. Szparaga, et al.
-
Effect of filling ratio on premixed methane/air explosion in an open-end pipe2016 / C. Guo, B.-q. Lin, C.-j. Zhu, B.-y. Jiang, Y.-m. Sun, et al.