Mechanical engineering topic list of research papers
-
Application of the EGM Method to a LED-Based Spotlight: A Constrained Pseudo-Optimization Design Process Based on the Analysis of the Local Entropy Generation Maps2011 / Giorgio Giangaspero, Enrico Sciubba
-
A Multi-Parameter Decoupling Method with a Lamb Wave Sensor for Improving the Selectivity of Label-Free Liquid Detection2012 / Lianqun Zhou, Yihui Wu, Ming Xuan, Jean-François Manceau, François Bastien
-
Buckling Analysis of Laminated Composite Panel with Elliptical Cutout Subject to Axial Compression2012 / Hamidreza Allahbakhsh, Ali Dadrasi
-
Low-Temperature Combustion Technology2012 / Konstantin Osintsev
-
Nonlinear Vibration Analysis for a Jeffcott Rotor with Seal and Air-Film Bearing Excitations2009 / Yuefang Wang, Xiaoyan Wang
-
A New Model of the Fractional Order Dynamics of the Planetary Gears2013 / Vera Nikolic-Stanojevic, Ljiljana Veljovic, Cemal Dolicanin
-
A Frequency Compensation Algorithm of Four-Wheel Coherence Random Road2013 / Jun Feng, Xinjie Zhang, Konghui Guo, Fangwu Ma, Hamid Reza Karimi
-
Stress Intensity Factors for Cracked Finite Plates with Mixed Boundary Condition2013 / Zheyuan Hu, Zheming Zhu, Ruoqi Feng, Rong Hu
-
The Front Seat Passenger: How to Transfer Qualitative Findings into Design2013 / Sebastian Osswald, Petra Sundström, Manfred Tscheligi
-
Experimental Results on an Integrated GPS and Multisensor System for Land Vehicle Positioning2009 / Umar Iqbal, Tashfeen B. Karamat, Aime F. Okou, Aboelmagd Noureldin
-
Fluctuations in the Energetic Properties of a Spark-Ignition Engine Model with Variability2013 / Pedro Curto-Risso, Alejandro Medina, Antonio Calvo-Hernández, Lev Guzmán-Vargas, Fernando Angulo-Brown
-
A Preconditioned Method for Rotating Flows at Arbitrary Mach Number2011 / Chunhua Sheng
-
Nonlinear Finite Element Analysis of Sloshing2013 / Siva Srinivas Kolukula, P. Chellapandi
-
Effects of Conjugate Heat Transfer on Steady MHD Mixed Convective Heat Transfer Flow over a Thin Vertical Plate Embedded in a Porous Medium with High Porosity2012 / Ahmet Kaya
-
Comparing Health Risks to Load-Haul-Dump Vehicle Operators Exposed to Whole-Body Vibration Using EU Directive 2002/44EC, ISO 2631-1 and ISO 2631-52013 / Tammy Eger, Aaron Kociolek, James Dickey
-
Development of thermoacoustic devices for power generation and refrigeration2013 / A. J. Jaworski, X. Mao
-
Finite Element Modeling of Ultrasonic Assisted Turning of Ti6Al4V Alloy
Abstract Improvements in the aviation industry raise the usage of titanium and its alloys. Main reasons of using titanium alloys are superior mechanical properties, high strength-to-density ratio, fatigue and corrosion resistance at moderately high...
2015 / Fatih Hayati Cakir, Selim Gurgen, Mehmet Alper Sofuoglu, Osman Nuri Celik, Melih Cemal Kushan -
Experimental investigation on using the piezoelectric and electromagnetic vibration absorbers in milling
Abstract The paper presents an active control system that counteracts the development of chatter vibration. The vibration amplitude depends on the dynamic properties of the machine tool, cutting tool and work-piece. In the paper we analyze the case...
2012 / Marcin Hoffmann, Krzysztof Marchelek, Miroslaw Pajor, Arkadiusz Parus -
Effects of T-S wave amplitude on the control of boundary layer transition by streaks
Abstract The effects of streaks on boundary layer transition depend on the initial amplitude of T-S waves introducedto excite the transition. This problem was studied in a flat-plate boundary layer in water tunnel byusing hydrogen bubble method....
2013 / Hui Guo, Yulong Feng, Haiwen Wang, Ziteng Liu -
Application of D-CRDM Method in Columnar Jointed Basalts Failure Analysis2013 / Changyu Jin, Xiating Feng, Chengxiang Yang, Dan Fang, Jiangpo Liu, et al.