Mechanical engineering topic list of research papers
-
Study of Turbulent Flow of Film Cooling Holes with Lateral Expanded Exits
Abstract Hot wire measurements and flow visualization are presented for studying the turbulent flow field over a flat gas turbine film cooling blade with lateral expanded holes. Three mass flux ratios of jet-to-free stream, M = 0.5, 0.89, 1.5, are...
2011 / Hong-hui SHI, Shunyuu SASA -
Modeling and Optimal Design of 3 Degrees of Freedom Helmholtz Resonator in Hydraulic System
Abstract Three degrees of freedom (3-DOF) Helmholtz resonator which consists of three cylindrical necks and cavities connected in series (neck-cavity-neck-cavity-neck-cavity) is suitable to reduce flow pulsation in hydraulic system. A novel lumped...
2012 / Changbin GUAN, Zongxia JIAO -
CFD Methodology for the Evaluation of Knock of a PFI Twin Spark Engine
Abstract A methodology for the evaluation of the effects of twin spark ignition system on CCV (Cycle by Cycle Variability) and knocking combustions is here presented, based on both the use of Computation Fluid Dynamics (CFD) tools and experimental...
2014 / Claudio Forte, Gian Marco Bianchi, Enrico Corti, Stefano Fantoni, Marco Costa -
CFD Analysis of Combustion and Pollutant Formation Phenomena in a Direct Injection Diesel Engine at Different EGR Conditions
Abstract In this work, exhaust gas recirculation (EGR) is varied in a direct injection constant speed diesel engine using extended coherent flame model for 3-zones by CFD. The three zones are unmixed fuel zone, mixed gases zone, unmixed air plus EGR ...
2013 / R. Manimaran, R. Thundil Karuppa Raj -
Study on the Characteristics of Expander Power Output Used for Offsetting Pumping Work Consumption in Organic Rankine Cycles2014 / Yu-Ting Wu, Biao Lei, Chong-Fang Ma, Lei Zhao, Jing-Fu Wang, et al.
-
Simulation of Entropy Generation under Stall Conditions in a Centrifugal Fan2014 / Lei Zhang, Jinhua Lang, Kuan Jiang, Songling Wang
-
A New Omni-Directional EMAT for Ultrasonic Lamb Wave Tomography Imaging of Metallic Plate Defects2014 / Songling Huang, Zheng Wei, Wei Zhao, Shen Wang
-
Analysis of operation of the gas turbine in a poligeneration combined cycle2014 / Łukasz Bartela, Janusz Kotowicz
-
An Optimal Calibration Method for a MEMS Inertial Measurement Unit2014 / Bin Fang, Wusheng Chou, Li Ding
-
Realization of the Atkinson-Miller cycle in spark-ignition engine by means of the fully variable inlet valve control system2015 / Zbigniew Żmudka, Stefan Postrzednik, Grzegorz Przybyła
-
SDP Policy Iteration-Based Energy Management Strategy Using Traffic Information for Commuter Hybrid Electric Vehicles2014 / Xiaohong Jiao, Tielong Shen
-
Analysis of pipeline transportation systems for carbon dioxide sequestration2014 / Andrzej Witkowski, Mirosław Majkut, Sebastian Rulik
-
Research on the Power Management Strategy of Hybrid Electric Vehicles Based on Electric Variable Transmissions2014 / Qiwei Xu, Shumei Cui, Liwei Song, Qianfan Zhang
-
Fabrication of Aluminum Foam-Filled Thin-Wall Steel Tube by Friction Welding and Its Compression Properties2014 / Yoshihiko Hangai, Masaki Saito, Takao Utsunomiya, Soichiro Kitahara, Osamu Kuwazuru, et al.
-
Microstructure and Tensile Behavior of Laser Arc Hybrid Welded Dissimilar Al and Ti Alloys2014 / Ming Gao, Cong Chen, Yunze Gu, Xiaoyan Zeng
-
Exergy analysis of operation of two-phase ejector in compression refrigeration systems2014 / Adam Dudar, Dariusz Butrymowicz, Kamil Śmierciew, Jarosław Karwacki
-
New generation of Sour Service Drill Pipe allows addressing highly sour field challenges2013 / A. Thomazic, R. Rodrigues, F. Thebault, S. Mauries, V. Flores, et al.
-
Effect of Diesel Engine Operating Conditions on the Particulate Size, Nanostructure and Oxidation Properties when Using Wasting Cooking Oil Biodiesel
Abstract Present work focuses on the effect of engine operating parameters, including the engine speed and engine load (air/fuel ratio), on the particulate nanostructure and oxidative reactivity when the engine is operated with WCO (waste cooking...
2015 / X.J. Man, C.S. Cheung, Z. Ning -
Restructuring surface tessellation with irregular boundary conditions
Abstract In this paper, the surface tessellation problem is explored, in particular, the task of meshing a surface with the added consideration of incorporating constructible building components. When a surface is tessellated into discrete...
2014 / Tsung-Hsien Wang, Ramesh Krishnamurti, Kenji Shimada -
Aerodynamic Configuration Design of Flight Demonstrator for Real Gas Effect
Abstract Real gas effect is one of the key technical challenges for reusable orbital vehicle development. Conducting flight demonstration is an effective way to understand the real gas flow characteristics. In this paper, investigation on the...
2015 / Chen Bingyan, Liu Zhou, Gong Anlong