Mechanical engineering topic list of research papers
-
Analysis to the dither in torsion coupling of low speed rotor
Abstract In order to explain the causation of dither present in the low speed rotor with solid lubrication, the relationship between rotor and bearing with the disturbance of torsion coupling is established, then the phenominon of unstability can be ...
2011 / HOU Bao-fen, LIU Zhao-hui, YANG Jian-Guo, SHE Wen-ji -
Design on Optimization of Argon Bottom Blowing of Molten Steel ladle
Abstract The cause of controlling argon blowing on steel-making process is analyzed. The strategy of controlling argon stirring energy is proposed, and the scheme controlling flow rate and fixing the pressure is achieved. The argon blowing of molten ...
2011 / Jiandong Shen, Yong Zhao, Guijin Han -
Influence of Powders and Process Parameters on Bonding Shear Strength and Micro Hardness in Laser Cladding Remanufacturing
Abstract Laser cladding technology has been proved an effective method to remanufacture the damaged parts by cladding high performance materials. The type of alloy powders, laser output power, and scanning speed were selected as influencing factors...
2015 / Mingsan Xu, Jianfeng Li, Jibin Jiang, Bingbing Li -
Adaptive Wavelet Transform Method to Identify Cracks in Gears2010 / Ales Belsak, Joze Flasker
-
Effects of Traffic Incident Information on Drivers’ Route Choice Behaviour in Urban Expressway Network
Abstract Traffic incidents such as traffic accidents are the major causes of severe congestion in urban expressway networks. Providing traffic incident information to travellers is considered to be important for maintaining the level of service in...
2012 / Takahiko Kusakabe, Taku Sharyo, Yasuo Asakura -
Digital Studio vs. Conventional in Teaching Architectural Design Process
Abstract The main objective of this paper is to present an action research conducted in a polytechnic in determining the effect of using digital studio on architectural diploma students for teaching the design process compared to the use of...
2012 / Mohd Arif Ismail, Rosnaini Mahmud, Isham Shah Hassan -
Quantifying the Severity of Traffic Conflict by Assuming Moving Elements as Rectangles at Intersection
Abstract To evaluate safety in intersections and find the relationship between conflict and accidents, a quantitative method for the severity of traffic conflict at intersection was proposed. Moving elements were assumed as rectangles. By using...
2012 / Guangquan Lu, Miaomiao Liu, Yunpeng Wang, Guizhen Yu -
A Mathematical Model for Temperature Induced Loosening due to Radial Expansion of Rectangle Thread Bolted Joints2015 / S. Hou, R. Liao, J. Li
-
Analytical Modeling of the Keyhole Including Multiple Reflections for Analysis of the Influence of Different Laser Intensity Distributions on Keyhole Geometry
Abstract An analytical model of the keyhole for deep penetration welding is presented. Based on a pressure and energy equilibrium the initial keyhole radii in different depths are calculated depending on different incident beam intensity...
2013 / J. Volpp, F. Vollertsen -
Transient aeroelastic responses and flutter analysis of a variable-span wing during the morphing process
Abstract To investigate the transient aeroelastic responses and flutter characteristics of a variable-span wing during the morphing process, a novel first-order state-space aeroelastic model is proposed. The time-varying structural model of the...
2013 / Ren Huang, Zhiping Qiu -
Experimental investigations of ignition delay period and performance of a diesel engine operated with Jatropha oil biodiesel
Abstract Jatropha-curcas as a non-edible methyl ester biodiesel fuel source is used to run single cylinder, variable compression ratio, and four-stroke diesel engine. Combustion characteristics as well as engine performance are measured for...
2013 / Mohammed EL-Kasaby, Medhat A. Nemit-allah -
A Model to Research Off-street Parking Across the Travel Time Based on the Impact of Non-motorized Traffic and Other Factors
Abstract In this paper, we takes the parking vehicle out of the off-street parking access in the city as the research object, analyzes the main influence factors of the vehicle in the process of entering in the parking lot, and the crossing time is...
2016 / Shejun Deng, Xiaofei Ye -
First Step Toward a Quantitative Approach to Evaluate Collaborative Tools
Abstract The product design process has been defined as a process which gathers multiple stakeholders working together during different steps to define a final product. Stakeholders have to approach the decision-making process effectively in order...
2014 / Damien Fleche, Jean-Bernard Bluntzer, Morad Mahdjoub, Jean-Claude Sagot -
Analysis of residual stresses around welds in a combustion casing
Abstract The electron-beam (EB) welding process and the subsequent post-weld heat treatment (PWHT) in an aero-engine combustion casing were simulated in 2D and validated by comparison with hole-drilling measurements. The full 3D modelling including...
2009 / Xu Song, Ioannis Kyriakoglou, Alexander M. Korsunsky -
Stress-Softening and Residual Strain Effects in Suture Materials2013 / Alex Elías-Zúñiga, Beatriz Montoya, Wendy Ortega-Lara, Eduardo Flores-Villalba, Ciro A. Rodríguez, et al.
-
Exergy Analysis of Overspray Process in Gas Turbine Systems2012 / Kyoung Hoon Kim, Kyoungjin Kim
-
Contribution of Small Wind Turbine Structural Vibration to Noise Emission2013 / Ehsan Mollasalehi, Qiao Sun, David Wood
-
A New Study on the Parameter Relationships of Planetary Roller Screws2012 / Shangjun Ma, Geng Liu, Ruiting Tong, Xiaocai Zhang
-
The Effect of Sputtering Parameters on the Film Properties of Molybdenum Back Contact for CIGS Solar Cells2013 / Peng-cheng Huang, Chia-ho Huang, Mao-yong Lin, Chia-ying Chou, Chun-yao Hsu, et al.
-
An Analytical Approach to the Analysis of Inhomogeneous Pipes under External Pressure2012 / Massimiliano Fraldi, Federico Guarracino