Materials engineering topic list of research papers
-
Influence of Cooling Conditions on a Slab’s Chill Zone Formation During Continuous Casting of Steel2017 / P. Drożdż
-
Conventional hydrothermal synthesis of titanate nanotubes: Systematic discussions on structural, optical, thermal and morphological properties
Abstract Titanate nanotubes were successfully synthesized by hydrothermal technique under acidic-base medium. The anatase and titanate phase of the starting TiO2 and tubular titanate was confirmed by powder XRD technique. The UV–vis-NIR spectroscopy ...
2017 / S. Muniyappan, T. Solaiyammal, K. Sudhakar, A. Karthigeyan, P. Murugakoothan -
Fracture toughness estimation of ballast stone used in Iranian railway
Abstract Ballast is a layer composed of crushed stone basically with diameters of 20–60 mm, on which sleepers and rails are set. Ballast is used to withstand vertical, horizontal and lateral forces applied on sleepers and to hold the line in...
2017 / I. Ferestade, P. Hosseini Tehrani, R. Heidary -
A Data Driven Solution to Synchronicity Deviations in Operational Modal Analysis
Abstract A scheme to minimize errors from time misalignments in the measured output of linear systems subjected to stationary excitations is presented. The objective is to provide estimates of synchronicity faults (if any) so the signals can be...
2017 / Dionisio Bernal -
Reinforcement Measures to Reduce the Human Induced Vibrations on Stair Steps – A Case Study
Abstract The human induced vibrations seen on stairs are usually a global phenomenon, however in some cases, if the connection between the treads and the rest of the structure has a very low rotational stiffness, a so-called local vibration...
2017 / Pedro Andrade, José Santos, Lino Maia -
Investigation on the Structural Damage of a Double-Hull Ship, Part II – Grounding Impact
Abstract Possibility of marine and offshore structures to experience accidental loads has been seriously considered up to this day. Remarkable casualties on related aspects are rising demand to ensure ship safety which in this subject is observed on ...
2017 / Aditya Rio Prabowo, Hyun Jin Cho, Seung Geon Lee, Dong Myung Bae, Jung Min Sohn, et al. -
Influence of the mechanics of escape on the instability of von Mises truss and its control
Abstract The elastic von Mises truss model is a prototype for bi-stable structures. It allows a deep understanding of the static and dynamic buckling of several planar and spatial truss systems and shallow lattice shell structures, including the...
2017 / Diego Orlando, Paulo B. Gonçalves, Stefano Lenci, Giuseppe Rega -
Analytical models of the S-N curve based on the hardness of the material
Abstract To calculate fatigue life in high-cycle region, the S-N characteristics for the material or construction element (depending on the calculation model employed) must be obtained. Due to this, analytical models are used for estimating the S-N...
2017 / Przemyslaw Strzelecki, Tomasz Tomaszewski -
Introducing manufacturing features into numerical modeling of hypervelocity impact damage of composite pressure vessels
Abstract Composite pressure vessels are extensively used in unmanned spacecraft systems due to high specific strength of composites, which provides higher mass savings as compared to metallic vessels. The most common example is their use as liquid...
2017 / Aleksandr Cherniaev, Igor Telichev -
Alternating the twin rotor damper between two modes of operation to eliminate small vibrations
Abstract In previous research, the twin rotor damper (TRD), an active mass damper, was presented. In a preferred, energy-efficient mode of operation, the continuous rotation mode, two eccentric control masses rotate with constant angular velocities...
2017 / Richard Bäumer, Richard Terrill, Uwe Starossek -
Propagation characteristics of acoustic emission wave in reinforced concrete
Abstract Due to the complexity of components and damage mechanism of reinforced concrete, the wave propagation characteristics in reinforced concrete are always complicated and difficult to determine. The objective of this article is to study the...
2017 / Haoxiong Feng, Weijian Yi -
Study of axial cutting forces and delamination phenomenon in drilling of carbon fiber composites
Abstract With this study we intend to relate the cutting conditions and the tool wear with the shearing forces appeared and the phenomenon of the delamination when we mechanized composite materials reinforced with carbon fiber (CFRP). In this case,...
2017 / V. Pascual, M. San-Juan, F.J. Santos, Ó. Martín, M.P. de Tiedra -
Synthesis of mesoporous Cr/ZSM-5 and W-Cr/ZSM-5 zeolite catalysts for oxidation of unsaturated fatty acid2017 / Phan Huy Hoang, Nguyen Thi Nhung, Le Quang Dien
-
Mechanical properties of Ni-Fe-Cu-P-B alloy produced by two component melt spinning (TCMS)2017 / M. Wojciechowska, K. Ziewiec, S. Kąc, K. Prusik
-
Primary Crystals of AlfeMnSi Intermetallics in the Cast AlSi Alloys2017 / M. Warmuzek
-
Natural and bio-inspired underwater adhesives: Current progress and new perspectives2017 / Mengkui Cui, Susu Ren, Shicao Wei, Chengjun Sun, Chao Zhong
-
Novel electrical and mechanical characteristics of composites composed of electrically conducting Ni-Cr alloy particles in non-conducting soda-lime glass2017 / Yoshiharu Waku, Teruyuki Yamashita, Hiroyuki Kitagawa, Masahiro Yoshinobu, Hiromichi Katsuyama, et al.
-
The Impact of the Thickness of the Ceramic Shell Mould on the (γ + γ′) Eutectic in the IN713C Superalloy Airfoil Blade Casting2017 / A. Szczotok, J. Nawrocki, J. Pietraszek
-
Double Fillet Welding of Carbon Steel T-Joint by Double Channel Shielding Gas Metal Arc Welding Method Using Metal Cored Wire2017 / T. Mert, N. Gultekin, A. Karaaslan
-
The Influence of Strontium on the Microstructure of Cast Magnesium Alloys Containing Aluminum and Calcium2015 / T. Rzychoń, B. Dybowski, A. Kiełbus