Materials engineering topic list of research papers
-
Procedure Model for Efficient Simulation Studies which Consider the Flows of Materials and Energy Simultaneously
Abstract The premise of this work is that more guidance is required for the application of the simultaneous simulation of material flows and energy flows. This assumption is supported by the findings of a systematic review which showed great...
2017 / Johannes Stoldt, Matthias Putz -
Discrimination and Quantification of Volatile Organic Compounds in the ppb-Range with Gas Sensitive SiC-Field Effect Transistors
Abstract Gas sensitive FETs based on SiC have been studied for the discrimination and quantification of hazardous volatile organic compounds (VOCs) in the low ppb range. The sensor performance was increased by temperature cycled operation (TCO) and...
2014 / C. Bur, M. Bastuck, D. Puglisi, A. Schütze, A. Lloyd Spetz, et al. -
Visualization of Water Accumulation Process in Polymer Electrolyte Fuel Cell Using Neutron Radiography
Abstract In order to clarify the water-accumulation phenomena in an operating polymer electrolyte fuel cell (PEFC), the water distribution in a small fuel cell was measured in the through-plane direction by using neutron radiography. The fuel cell...
2015 / Hideki Murakawa, Katsumi Sugimoto, Nobuki Kitamura, Masataka Sawada, Hitoshi Asano, et al. -
Mechanical properties analysis of Al-9Zn-5Cu-4Mg cast alloy by T5 heat treatment2017 / Nurhabibah Paramitha Eka Utami, Hendri Chandra
-
Performance change of few layer black phosphorus transistors in ambient2015 / Xiaomeng Ma, Wanglin Lu, Bingyan Chen, Donglai Zhong, Le Huang, et al.
-
Creep-age forming AA2219 plates with different stiffener designs and pre-form age conditions: Experimental and finite element studies
Abstract Creep-age forming (CAF) is one of the relatively new forming techniques that has been proven viable for the production of extra-large integral airframe structures. However, experimental studies on forming stiffened structures under...
2014 / Aaron C.L. Lam, Zhusheng Shi, Haoliang Yang, Li Wan, Catrin M. Davies, et al. -
Mechanical behaviour of hot dip galvanized steel connection under cyclic loading
Abstract: This short technical note summarizes some recent data from hot dip galvanized steel bolted connections under fatigue loading. In particular the effect of a galvanizing coating on the fatigue strength of S355 structural steel is analyzed in ...
2017 / F. Berto, S.M.J. Razavi, M.R. Ayatollahi, F. Mutignani -
HMGB1 promotes cellular chemokine synthesis and potentiates mesenchymal stromal cell migration via Rap1 activation2016 / Feng Lin, Deting Xue, Tao Xie, Zhijun Pan
-
Experimental Testing Suitability of the Waste Glass into the Polymer Anchor Materials Based on Epoxy Resin
Abstract This article deals with the suitable use of waste glass in polymer anchor materials based on the epoxy resin. The research focused on the effect various waste glass had in different amounts on specific anchor-material properties. Various...
2017 / Tomáš Žlebek, Jakub Hodul, Rostislav Drochytka -
Uncertain behaviours of integrated circuits improve computational performance2015 / Chihiro Yoshimura, Masanao Yamaoka, Masato Hayashi, Takuya Okuyama, Hidetaka Aoki, et al.
-
Wear behavior of Al-7%Si-0.3%Mg/melon shell ash particulate composites
Abstract The present study examined wear characteristics of A356/melon shell ash particulate composites. Dry-sliding the stainless steel ball against specimen disc revealed the abrasive wear behavior of the composites under loads of 2 and 5N. The...
2017 / M. Abdulwahab, R.M. Dodo, I.Y. Suleiman, A.I. Gebi, I. Umar -
HCBPM: An Idea toward a Social Learning Environment for Humanoid Robot2010 / Fady Alnajjar, Abdul Rahman Hafiz, Kazuyuki Murase
-
Conical Refraction of Elastic Waves by Anisotropic Metamaterials and Application for Parallel Translation of Elastic Waves2017 / Young Kwan Ahn, Hyung Jin Lee, Yoon Young Kim
-
TEM Microstructure and Chemical Composition of Transition Zone Between Steel Tube and An Inconel 625 Weld Overlay Coating Produced by CMT Method2017 / M. Rozmus-Górnikowska, M. Blicharski
-
Increasing of the Mechanical Properties of Friction Stir Welded Joints of 6061 Aluminum Alloy by Introducing Alumina Particles2017 / M. A. Tashkandi, J. A. Al-Jarrah, M. Ibrahim
-
Design for invention: annotation of functional geometry interaction for representing novel working principles2017 / Mark Atherton, Pingfei Jiang, David Harrison, Alessio Malizia
-
Effectiveness of the neutron-shield nanocomposites for a dual-purpose cask of Bushehr's Water–Water Energetic Reactor (VVER) 1000 nuclear-power-plant spent fuels
Abstract In order to perform dry interim storage and transportation of the spent-fuel assemblies of the Bushehr Nuclear Power Plant, dual-purpose casks can be utilized. The effectiveness of different neutron-shield materials for the dual-purpose...
2017 / Mahdi Rezaeian, Jamshid Kamali, Seyed Javad Ahmadi, Mohammad Amin Kiani -
Influence of Material Coating on the Heat Transfer in a Layered Cu-SiC-Cu Systems2017 / A. Strojny-Nędza, K. Pietrzak, M. Teodorczyk, M. Basista, W. Węglewski, et al.
-
Parametric analyses on dynamic stall control of rotor airfoil via synthetic jet
Abstract The effects of synthetic jet control on unsteady dynamic stall over rotor airfoil are investigated numerically. A moving-embedded grid method and an Unsteady Reynolds Averaged Navier-Stokes (URANS) solver coupled with k-ω Shear Stress...
2017 / Qijun ZHAO, Yiyang MA, Guoqing ZHAO -
Analysis of Thermal Stresses and Strains Developing during the Heat Treatment of Windmill Shaft2017 / A. Cebo-Rudnicka, Z. Malinowski, T. Telejko