Materials engineering topic list of research papers
-
Assessment of Changes in Technical Systems and their Effects on Cost and Duration based on Structural Complexity
Abstract Large engineering products like naval vessels are very complex systems. As there are long development times, multiple design changes occur frequently because of changes in requirements. This leads to cost and schedule overruns. One reason...
2016 / Eric Rebentisch, Günther Schuh, Michael Riesener, Stefan Breunig, Alexander Pott, et al. -
Radiation-induced segregation on defect clusters in single-phase concentrated solid-solution alloys
Abstract A group of single-phase concentrated solid-solution alloys (SP-CSAs), including NiFe, NiCoFe, NiCoFeCr, as well as a high entropy alloy NiCoFeCrMn, was irradiated with 3 MeV Ni2+ ions at 773 K to a fluence of 5 × 1016 ions/cm2 for the study ...
2017 / Chenyang Lu, Taini Yang, Ke Jin, Ning Gao, Pengyuan Xiu, et al. -
An Automated Algorithm for Measurement of Surgical Tip Excursion in Ultrasonic Vibration Using the Spatial 2-Dimensional Fourier Transform in an Optical Image
Abstract The International Electrotechnical Commission (IEC) has defined a standard IEC 61847 (First Edition, 1998) for characterization of ultrasonic surgical systems. This standard prescribes several methods for measurement of primary tip...
2016 / Prakash Manandhar, Andrew Ward, Patrick Allen, Daniel J. Cotter -
Simulation of Propagation and Transformation of THz Bessel Beams with Orbital Angular Momentum
Abstract Recently, terahertz Bessel beams with angular orbital momentum (“vortex beams”) with topological charges l = ±1 and l = ±2 were generated for the first time using radiation of the Novosibirsk free electron laser (NovoFEL) and silicon binary ...
2016 / Yulia Choporova, Boris Knyazev, Mikhail Mitkov, Natalya Osintseva, Vladimir Pavelyev -
Experimental Investigation of the Unsteady Flow Behavior on a Film Cooling Flat Plate
Abstract An experimental study was conducted to investigate the unsteady behavior of film cooling for cylindrical holes on a flat plate wind tunnel. Tests have been carried out at low speed and low inlet turbulence intensity level, with blowing...
2016 / S. Rouina, M. Miranda, G. Barigozzi -
The Use of Waste Materials in the Construction Industry
Abstract Waste materials are a major environmental problem, which is a threat to the environment. It is important to reuse these materials and dispose of them. Waste can be used in the construction industry in two ways: by reusing (reuse components) ...
2016 / Ryszard Dachowski, Paulina Kostrzewa -
Interfacial charge trapping in the polymer solar cells and its elimination by solvent annealing2016 / A. K. Chauhan, Abhay Gusain, P. Jha, P. Veerender, S. P. Koiry, et al.
-
Bayesian analysis of low-cycle fatigue failure in printed wiring boards
Abstract In this study, a low-cycle fatigue experiment was conducted on printed wiring boards (PWB). The Weibull regression model and computational Bayesian analysis method were applied to analyze failure time data and to identify important factors...
2016 / Rong Pan, Xinyue Xu, Joseph Juarez -
A successful symposium of “Multi-origin of soft-sediment deformation structures and seismites”
Abstract A great progress has been made in researches of soft-sediment deformation structures (SSDS) and seismites in China. However, the research thought was not open-minded. About the origin of SSDS, it was almost with one viewpoint, i.e., almost...
2016 / Zeng-Zhao Feng -
SUFTUS-2016 Foreword2016 / Shuping Jiang
-
NH3 Storage on a Zeolite SCR Catalyst Measured Using a Microwave-based Method: Reduced Sensitivity for More Strongly Held NH3
Abstract One method for reduction of nitrogen oxides from the exhaust of modern diesel vehicles is the selective catalytic reduction (SCR) of NOx by NH3 injected onto a zeolite SCR catalyst. Knowledge of the amount of NH3 stored on these catalysts...
2017 / D. Kubinski, A. Bogner -
Upgrade of the Detector for Imaging of Explosions
Abstract Methods of dynamic imaging of explosions at a synchrotron radiation (SR) beam and small-angle X-ray scattering experiments with exploding samples are being developed in the Siberian Synchrotron Radiation Center (SSRC) at the Budker...
2016 / L.I. Shekhtman, V.M. Aulchenko, V.N. Kudryavtsev, V.D. Kutovenko, V.M. Titov, et al. -
Experimental and theoretical investigation of temperature-dependent electrical fatigue studies on 1-3 type piezocomposites2016 / Y. Mohan, A. Arockiarajan
-
Cost Analysis and Development Strategies for China’ Natural Gas Power Generation Industry Under the Situation of Energy Price's Reformation
Abstract Driven by Chinese government, China's natural gas power generation industry has to deal with the energy price's reformation, the price of natural gas, electric power and some other energy source will be made by market instead of government. ...
2016 / Naiping Zhu, Qi Zhao, Lixin Tian, Qing Zhang -
Alteration of Leaf Anatomy of Handeuleum (Graptophyllum pictum L. Griff) due to Gamma Irradiation2016 / Arrin Rosmala, Nurul Khumaida, Dewi Sukma
-
Simulation study of 14-nm-gate III-V trigate field effect transistor devices with In1−xGaxAs channel capping layer2015 / Cheng-Hao Huang, Yiming Li
-
Analysis of Thermal Damage in FRP Drilling
Abstract Among machining operations applied to polymeric composite materials, drilling is the more important one due to the need to implement mechanical couplings, which in most cases are not yet possible using structural adhesives. Such process is...
2016 / L. Sorrentino, S. Turchetta, L. Colella, C. Bellini -
Improving EDM Process on AZ31 Magnesium Alloy towards Sustainable Biodegradable Implant Manufacturing
Abstract The electrical discharge machining (EDM) process is an excellent method to machine with the high geometrical accuracy required for bio-medical implants. In implant fabrication, a higher surface roughness has led to a huge contact surface...
2016 / A.M. Abdul-Rani, M.A. Razak, G. Littlefair, I. Gibson, A.M. Nanimina -
Molecularly Imprinted Polymer Based Sensor to Detect Isoborneol in Aqueous Samples
Abstract Herein we report the development of a selective chemical sensor based on molecularly imprinted polymers (MIP) and quartz crystal microbalance (QCM) to detect isoborneol (ISO) in aqueous samples. Their response scales linearly with...
2017 / G.S. Braga, P.A. Lieberzeit, F.J. Fonseca -
An Experimental Study on the Performance of Two Temperature Sensors Based on 4H-SiC Diodes
Abstract The performance of two temperature sensors based on 4H-SiC diodes are investigated. Both devices show a good linear dependence on temperature of the difference between the forward bias voltages measured on two identical diodes (Schottky or...
2017 / S. Rao, G. Pangallo, F.G. Della Corte