Materials engineering topic list of research papers
-
The use of ECT and 6PBP tests to evaluate fracture behavior of adhesively bonded steel/epoxy joints under Mode-III and Mixed Mode III/II2014 / Farhad Asgari Mehrabadi
-
Dynamic fracture in rubber toughened polymers: the influence of the fracture surface roughness
Abstract Dynamic fracture tests have been performed with rubber toughened polymethylmethacrylate (RT-PMMA) samples. For these kinds of materials the macroscopic crack tip velocity å ≈ 0.6cr is observed to not change during...
2016 / Jean-Benoît Kopp, Christophe Fond, Jean Schmittbuhl, Olivier Noel -
Surrogate Modeling of Ultrasonic Nondestructive Evaluation Simulations
Abstract Ultrasonic testing (UT) is used to detect internal flaws in materials or to characterize material properties. Computational simulations are an important part of the UT process. Fast models are essential for UT applications such as inverse...
2016 / Jacob Siegler, Leifur Leifsson, Robert Grandin, Slawomir Koziel, Adrian Bekasiewicz -
Direct Metal Deposition of Refractory High Entropy Alloy MoNbTaW
Abstract Alloying of refractory high entropy alloys (HEAs) such as MoNbTaW is usually done by vacuum arc melting (VAM) or powder metallurgy (PM) due to the high melting points of the elements. Machining to produce the final shape of parts is often...
2016 / Henrik Dobbelstein, Magnus Thiele, Evgeny L. Gurevich, Easo P. George, Andreas Ostendorf -
A novel training algorithm for convolutional neural network2016 / Alwin Anuse, Vibha Vyas
-
A Technique to Preserve Edge Information in Single Image Super Resolution
Abstract Goal of image super resolution is to enhance the size of an image without upsetting the inherited information. The quality of an enhanced image is conserved if the information around all kind of edges is preserved. The proposed novel...
2016 / Amisha J. Shah, Suryakant B. Gupta -
Smart Rainwater Tanks as a Rainguage Network and Dam for Flood Control
Abstract We propose the use of smart rainwater tanks (SRTs) equipped with water-level sensors, outflow monitors, and water pump controls. In our design, SRTs are connected via a network that enables monitoring data to be collected and pump-control...
2016 / Toshiyuki Moriyama, Koji Nishiyama, Shinobu Izumi, Katsuhiro Morisita, Shigeki Hirose -
Adjusting Surface Integrity of Gears Using Wire EDM to Increase the Flank Load Carrying Capacity
Abstract High performance gears require high geometrical qualities. For these aspects expensive grinding processes are indispensable as finishing processes. This paper deals with the investigation of wire EDM (WEDM) as a technological substitution...
2016 / D. Sari, D. Welling, C. Löpenhaus, F. Klocke, A. Klink -
Machining of Micro-holes on Sodalime Glass Using Developed Micro-abrasive Jet Machine (μ-AJM)
Abstract Micro abrasive jet machining is a non-conventional machining process used to produce micro features such as holes, channels on various brittle materials in particular and engineering materials in general. This process finds wide industrial...
2016 / Abhishek Kumar, Somashekhar S. Hiremath -
An Analysis of Leaf Chlorophyll Measurement Method Using Chlorophyll Meter and Image Processing Technique
Abstract A regular and periodic monitoring of crop health is essential in any cultivation. An important parameter which act as indices of crop health is the leaf chlorophyll measurement. In the Asian part of the world, Betel vine (Piper betle L.,...
2016 / Amar Kumar Dey, Manisha Sharma, M.R. Meshram -
Policies and Status of Window Design for Energy Efficient Buildings
Abstract Windows are known to be responsible for considerable portion of heating and cooling energy use in modern buildings. Many countries have tightened minimum requirements for window performance and design in building energy conservation codes...
2016 / Sun Sook Kim, Min Jeong Bae, Young Don Kim -
Influence of Ta2O5 doping on mechanical and biological properties of silicate glass-ceramics2016 / Madeeha Riaz, Rehana Zia, Farhat Saleemi, Farooq Bashir, Riaz Ahmad, et al.
-
Evaluation of Skid Resistance Using CTM, DFT and SRT-3 Devices
Abstract Evaluation of skid resistance could be based on both microtexture and macrotexture. It is possible to measure this parameter using CTM (Circular Track Meter) and DFT (Dynamic Friction Tester) devices. Macrotexture is characterized by the...
2016 / Marta Wasilewska, Wladyslaw Gardziejczyk, Pawel Gierasimiuk -
Identification of Microstructural Model Parameters for 3D Finite Element Simulation of Machining Inconel 100 Alloy
Abstract Prediction of machining induced surface integrity and microstructural changes using Finite Element modeling is challenging due to difficult to obtain material deformation models as well as models related to microstructure of the material....
2016 / T. Özel, Y.M. Arısoy, C. Guo -
Asymptotic Stress Field in the Vicinity of the Mixed-Mode Crack in Damaged Materials Under Creep Conditions
Abstract The creep crack problems in damaged materials under mixed mode loading under creep-damage coupled formulation are considered. The class of the self-similar solutions to the plane creep crack problems in a damaged medium under mixed-mode...
2016 / Stepanova Larisa, Yakovleva Ekaterina -
Towards Agile Engineering of Mechatronic Systems in Machinery and Plant Construction
Abstract Agile procedures (e.g. Scrum) are commonly used in rapidly changing environments of software engineering. Experts appreciate improvements in interdisciplinary collaboration, lead times and development costs by applying agile techniques as...
2016 / Thorsten P. Klein, Gunther Reinhart -
Design and operation of a Tesla-type valve for pulsating heat pipes
Abstract A new Tesla-type valve is successfully designed for promoting circulation in a pulsating heat pipe (PHP) and improving the thermal resistance. Its functionality and diodicity is tested by laminar single-phase modelling and by steady...
2016 / S.F. de Vries, D. Florea, F.G.A. Homburg, A.J.H. Frijns -
Microstructure and mechanical property in heat affected zone (HAZ) in F82H jointed with SUS316L by fiber laser welding
Abstract This study investigates the microstructure and mechanical property in heat affected zone (HAZ) between F82H and SUS316L jointed by 4 kW fiber laser welding at different parameters such as laser scan rate and beam position. OM/FE-SEM...
2016 / S. Kano, A. Oba, H.L. Yang, Y. Matsukawa, Y. Satoh, et al. -
Deployable Structures Using Non-singular Rigid Foldable Patterns
Abstract The opportunities of fully foldable structures are well utilized in some industries, but are only rarely applied in the built environment. In the first part of this study, a number of folding typologies are investigated and their...
2016 / Ruud van Knippenberg, Arjan Habraken, Patrick Teuffel -
A Review on Abrasive Flow Machining (AFM)
Abstract The required finish/texture is one of the prime requirements in various, finished components through conventional machining, processes like grinding, lapping, polishing and super finishing processes. Industries are spending huge amount of...
2016 / S. Santhosh Kumar, Somashekhar S. Hiremath