Materials engineering topic list of research papers
-
Double carbon decorated lithium titanate as anode material with high rate performance for lithium-ion batteries
Abstract Spinel lithium titanate (Li4Ti5O12) has the advantages of structural stability, however it suffers the disadvantages of low lithium-ion diffusion coefficient as well as low conductivity. In order to solve issues, we reported a simple method ...
2016 / Haifang Ni, Weili Song, Lizhen Fan -
CMOS Buffer Design Approach for Low Power and Lower Delay SRAM Design
Abstract Leakage power dissipation of on-chip SRAM constitutes a significant amount of the total chip power consumption in microprocessors and System on chips. With technology scaling, it is becoming increasingly challenging to maintain the yield...
2016 / p.p. Mariyamol, N. Aswathy -
Thermal characterisation of binary sodium/lithium nitrate salts for latent heat storage at medium temperatures
Abstract Latent heat storage in molten salt mixtures has been considered as a promising method for medium temperature solar thermal storage and industrial waste heat storage. The binary sodium/lithium nitrate salt mixture is one of the potential...
2016 / Dan Zhou, Philip Eames -
Improving Impact Resistance of Polymer Concrete Using CNTs2016 / Sherif M. Daghash, Eslam M. Soliman, Usama F. Kandil, Mahmoud M. Reda Taha
-
Exceeding 3 ms Minority Carrier Lifetime in n–type Non-contact Crucible Silicon
Abstract The presence of metal impurities and their interactions with structural defects (e.g., dislocations) are deleterious to the performance of Si-based solar cell devices. To achieve higher minority carrier lifetimes that translate into higher...
2016 / Sergio Castellanos, Maulid Kivambe, Mallory A. Jensen, Douglas M. Powell, Kazuo Nakajima, et al. -
Crystal structure of tetra(5-methyl-2-pyrazinecarboxylato)-(4,4′-bipyridine)dizinc(II) dihydrate, Zn2(C6H5N2O2)4(C10H8N2) · 2H2O2014 / Guang Fan, Zu-Pei Yang, Yin-Li Zhang, Yong Liu
-
Realization of Ternary Reversible Circuits Using Improved Gate Library
Abstract Ternary logic has some distinct advantage over binary logic. In this paper we propose a synthesis approach for ternary reversible circuits using ternary reversible gates. Our method takes a boolean function as input. The input is provided...
2016 / P. Mercy Nesa Rani, Abhoy Kole, Kamalika Datta, Alok Chakrabarty -
Full- and small-scale tests on strain capacity of X80 seamless pipes
Abstract Application of high-strength steels such as X80 grade may help reduce cost in offshore pipeline projects through wall thickness optimisation and associated installation costs. To ensure reliability of such application during the pipeline...
2016 / A. Bastola, J. Wang, H. Shitamoto, A. Mirzaee-Sisan, M. Hamada, et al. -
Testing and verification modeling of wave-shape formation under explosion welding to laminate AA 2519-Ti6Al4V
Abstract The work describes the process of joining the explosive layered materials. It will be presented attempt analytical process of connecting the wave and its impact on the effects of combining explosive. The calculations will be chosen for the...
2016 / I. Szachogluchowicz, L. Sniezek, H. Sulym, M. Gloc -
Effects of the composition of Ca-rich inclusions on tool wear mechanisms during the hard-turning of steels for transmission components
Abstract This study describes the influence of the steel characteristics of Ca-treated carburising steel grades during hard part turning of synchronising rings in gearbox production. The main focus was on the chemical composition of the non-metallic ...
2016 / Niclas Ånmark, Thomas Björk -
Large scale fabrication of graphene for oil and organic solvent absorption
Abstract A simple method for synthesizing highly wrinkled and less layered structure of graphene sheets by using a mechano-thermal exfoliation method was developed. During this process, graphite and ammonium chloride (NH4Cl) powders were loaded by...
2016 / Chenxi Fu, Zifeng Wang, Junyi Liu, Hongbo Jiang, Guangming Li, et al. -
Application FRP-rebar in the Manufacture of Reinforced Concrete Structures
Abstract Reinforced concrete is one of the first places in terms of use in various areas of construction. This is primarily determined by its relative cheapness and durability. Concrete Durability significantly associated with metal reinforcement...
2016 / Yulia O. Kustikova -
Integrating Product and Technology Development: A Proposed Reference Model for Dual Innovation
Abstract Although dual innovation projects, defined in this article as the concurrent development of products and technologies, often occur in industry, these are only scarcely supported methodologically. Limited research has been done about dual...
2016 / Ellen Brilhuis-Meijer, Daniela C.A. Pigosso, Tim C. McAloone -
Influence of Milling Time on the Crystallite Size of AlSi5Cu2/SiC Composite Powder2016 / M. Suśniak, P. Pałka, J. Karwan-Baczewska
-
In situ formation of ZrB2 particulates and their influence on microstructure and tensile behavior of AA7075 aluminum matrix composites
Abstract In situ synthesis of aluminum matrix composites (AMCs) has become a popular method due to several advantages over conventional stir casting method. In the present study, AA7075/ZrB2 AMCs reinforced with various content of ZrB2 particulates...
2016 / J. David Raja Selvam, I. Dinaharan -
On the Application of Agility Principles in Ramp-up Management: Approaching the Challenges in the High-end Powder Metallurgy Industry
Abstract In recent years, the field of ramp-up management has received wide attention in both science and industrial practice. However, current research mainly focuses on discrete manufacturing and assembly industries, whereas companies in...
2016 / Martin Kremsmayr, André Dronhofer, Nikolaus Mitterer, Christian Ramsauer -
Effects of water transportation on subduction dynamics: Roles of viscosity and density reduction
Abstract The effects of water on subduction dynamics, e.g., plate migration rate, slab geometry, stress field, and back-arc spreading, are investigated by using a 2-D self-consistent model for lithosphere subduction and whole mantle convection. We...
2016 / Atsushi Nakao, Hikaru Iwamori, Tomoeki Nakakuki -
Structural response of fire-exposed cross-laminated timber beams under sustained loads
Abstract Cross-laminated timber (CLT) is a popular construction material for low and medium-rise construction. However an architectural aspiration exists for tall mass timber buildings, and this is currently hindered by knowledge gaps and...
2016 / Sean A. Lineham, Daniel Thomson, Alastair I. Bartlett, Luke A. Bisby, Rory M. Hadden -
Surface Integrity Analysis when Machining Inconel 718 with Conventional and Cryogenic Cooling
Abstract Cryogenic machining together with minimum quantity lubrication (MQL), is claimed to be a promising alternative to flood cooling in industrial applications since it avoids the use of large amounts of cutting fluids and it improves the...
2016 / A. Iturbe, E. Hormaetxe, A. Garay, P.J. Arrazola -
The Influence of Tool Holder Technologies on Milling Performance
Abstract The quality of machined surfaces is significantly influenced by machine vibrations caused by the cutting process. Whereas most publications ignore the influence of the tool holder, this paper considers the dynamic behaviour of the whole...
2016 / J. Fleischer, V. Schulze, M. Klaiber, J. Bauer, F. Zanger, et al.