Materials engineering topic list of research papers
-
My science class and expected career choices—a structural equation model of determinants involving Abu Dhabi high school students2016 / Masood Badri, Ali Alnuaimi, Jihad Mohaidat, Asma Al Rashedi, Guang Yang, et al.
-
A review of optimisation techniques used in the composite recycling area: State-of-the-art and steps towards a research agenda
Abstract The increased use of carbon fibre and glass fibre reinforced polymer in industry coupled with restrictions on landfill disposal has resulted in a need to develop effective recycling technologies for composites. Currently, mechanical,...
2016 / Ying Liu, Michael Farnsworth, Ashutosh Tiwari -
Complete Williams Asymptotic Expansion Near The Crack Tips of Collinear Cracks of Equal Lengths in an Infinite Plane Medium
Abstract The study is aimed at analytical determination of coefficients in crack tip stress expansions for two collinear finite cracks of equal lengths in an infinite plane medium. The study is based on the solutions of the complex variable theory...
2016 / Larisa Stepanova, Pavel Roslyakov -
Professor Robert Schaller: Zener Medalist2016 / D. Mari
-
Modeling of Manufacturing Technologies During Ramp-up
Abstract The production ramp-up is of increasing importance for the manufacturing industry and has a significant impact on the product's success in terms of costs and time to reach full capacity utilization (time-to-volume). During the production...
2016 / F. Klocke, J. Stauder, P. Mattfeld, J. Müller -
Strut effectiveness factor for reinforced concrete deep beams under dynamic loading conditions
Abstract In a current study, a new strut effectiveness factor based on Strut-and-Tie Model (STM) is proposed to assess the ultimate shear strength of reinforced concrete (RC) deep beam subjected to dynamic loads. The derivation of the new...
2016 / Ammar N. Hanoon, M.S. Jaafar, Farzad Hejazi, F.N.A. Abd Aziz -
Research on Extruded Products of Mgalzn Alloys – Microstructure and Mechanical Properties / Badania Wyrobów Wyciskanych Ze Stopów Mgalzn – Mikrostruktura I Właściwości Mechaniczne2016 / B. Płonka, K. Remsak, P. Korczak, M. Lech-Grega, M. Rajda
-
Assembly 8: where surgeons and pulmonologists meet2016 / Geert M. Verleden
-
Rationalization of Polymer Composite Materials Processing by Improving Production Efficiency
Abstract Economic efficiency is one of the main criteria in the design of technological parts processing. To determine this criterion we have identified the main production expenses, including the cost of the cutting tool, the cost of its training,...
2016 / A.S. Yanyushkin, D.A. Rychkov, D.V. Lobanov -
Fracture Mechanics in Ancient Egypt
Abstract Probably the first extensive investigation in the field of fracture mechanics was developed by the ancient Egyptian in the period before 3500 BC. The application of this knowledge from investigation on the exact splitting of rock using the...
2016 / B.M. El-Sehily -
A Study on Environmental Assessment of Residue from Gasification of Polyurethane Waste in E-Waste Recycling Process
Abstract With expanding economic growth, the consumption and changing period of electronics products have increased rapidly in last couple of decades in Korea. A refrigerator generally contains 10% of polyurethane. Since the amount of used...
2016 / J.J. Kang, J.S. Lee, W.S. Yang, S.W. Park, M.T. Alam, et al. -
Porosity and cell size control in alumina foam preparation by thermo-foaming of powder dispersions in molten sucrose
Abstract The foaming characteristics of alumina powder dispersions in molten sucrose have been studied as a function of alumina powder to sucrose weight ratio (W A/S) and foaming temperature. The increase in foaming temperature...
2016 / Sujith Vijayan, Praveen Wilson, K. Prabhakaran -
Experimental Study on Cooling of Solar Collectors Using Air-water Mixture
Abstract Large numbers of studies are reported on solar collectors using a single fluid to cool it, be it with water or with air only. The present paper reports a series of experiments that investigate into the performance of solar collectors that...
2016 / Varghese Panthalookaran, Jino P. George -
Special issue introduction: Photoacoustic microscopy2016 / Hao F. Zhang, Daniel Razansky
-
Modelling Topology of Freeform Surfaces with Ball-end Milling
Abstract Machining of freeform surfaces, viz. dies, moulds, blades, etc. is one the most difficult processes nowadays. Ball-end milling having either the constant tool pitch for flat and oblique surfaces or the variable tool pitch for freeform...
2016 / A.V. Vyboishchik -
Light-addressable potentiometric sensor (LAPS) combined with magnetic beads for pharmaceutical screening
Abstract The light-addressable potentiometric sensor (LAPS) has the unique feature to address different regions of a sensor surface without the need of complex structures. Measurements at different locations on the sensor surface can be performed in ...
2016 / Torsten Wagner, Wolfgang Vornholt, Carl Frederik Werner, Tatsuo Yoshinobu, Ko-ichiro Miyamoto, et al. -
Laser borided composite layer produced on austenitic 316L steel2016 / Daria Mikołajczak, Michał Kulka, Natalia Makuch, Piotr Dziarski
-
Prediction of ductile failure using a phenomenological model calibrated from micromechanical simulations
Abstract Unit-cell models were in this study utilized to numerically determine the failure locus of a cast and homogenized AA6060 aluminum alloy. Simulations were conducted for moderate and high stress triaxiality ratios, and for various Lode...
2016 / J.K. Holmen, L.E.B. Dæhli, O.S. Hopperstad, T. Børvik -
Microstructure and magnetic properties of Nd-Fe-B-(Re, Ti) alloys2015 / Mariusz Hasiak
-
Thermo-Mechanical Processing of Rapidly Solidified 5083 Aluminium Alloy - Structure and Mechanical Properties2015 / T. Tokarski