Materials engineering topic list of research papers
-
Bounding quantum gate error rate based on reported average fidelity2015 / Yuval R Sanders, Joel J Wallman, Barry C Sanders
-
Electron irradiation-induced defects in Mo-diluted FeCrNi austenitic alloy during void swelling incubation2016 / B Y Wang, E Y Lu, C X Zhang, Q Xu, S X Jin, et al.
-
A decision support system for waste heat recovery in manufacturing
Abstract One third of energy consumption is attributable to the industrial sector, with as much as half ultimately wasted as heat. Consequently, research has focused on technologies for harvesting this waste heat energy, however, the adoption of...
2016 / Alessandro Simeone, Yang Luo, Elliot Woolley, Shahin Rahimifard, Claudio Boër -
Analysis of Stir Cast Aluminium Silicon Carbide Metal Matrix Composite: A Comprehensive Review
Abstract Aluminium silicon carbide metal matrix composites are used in various fields like aerospace, aircrafts, underwater, automobile, substrate in electronics, golf clubs, turbine blades, brake pads etc. Several fabrication techniques are...
2016 / M.T. Sijo, K.R. Jayadevan -
High-k perovskite gate oxide BaHfO32017 / Young Mo Kim, Chulkwon Park, Taewoo Ha, Useong Kim, Namwook Kim, et al.
-
On the Tribological Performance of Vegetal Lubricants: Experimental Investigation on Jatropha Curcas L. oil
Abstract The limited resources of petroleum-based lubricants and increased environmental contamination, that they produce, lead to increased demand for bio-lubricants. Due to several factors such as biodegradability, good lubricating properties and...
2016 / A. Ruggiero, R. D’Amato, M. Merola, P. Valášek, M. Müller -
Investigation into the material properties of wooden composite structures with in-situ fibre reinforcement using additive manufacturing
Abstract In contrast to subtractive manufacturing techniques, additive manufacturing processes are known for their high efficiency in regards to utilisation of feedstock. However the various polymer, metallic and composite feedstocks used within...
2016 / Kate Pitt, Omar Lopez-Botello, Austin D. Lafferty, Iain Todd, Kamran Mumtaz -
Model Predictive Control for Energy Management of a Plug-in Hybrid Electric Bus
Abstract In this paper, the model predictive control (MPC) method is researched for energy management problem of a plug-in hybrid electric vehicle (HEV). The multi-step Markov prediction method is used to predict the driving condition. Dynamic...
2016 / Hongwen He, Jieli Zhang, Gaopeng Li -
Computer Simulation of the Relationship between Selected Properties of PVD Coatings2016 / A. Śliwa, W. Kwaśny, W. Sitek, M. Bonek
-
Estimation of Wind Power Density at a Wind Farm Site Located in Western Rajasthan Region of India
Abstract Wind power density is an important parameter for the potential estimation of a wind farm and is used to compare different sites. This paper estimates wind power density of Soda site located at Western Rajasthan in India. Modified Maximum...
2016 / Bharat Kumar Saxena, K.V.S. Rao -
Surface treatments applied on titanium implants2015 / Sorin Cosmin Cosma, Nicolae Balc, Marioara Moldovan, Cristina Ștefana Miron-Borzan
-
Properties of Light MMCs Modified with Cordierite Synthesized from Fly Ash2016 / Piotr Długosz, Angelika Rączka, Adrian Kopeć, Rudolf Krzyżak, Paweł Darłak, et al.
-
Heat load and deuterium plasma effects on SPS and WSP tungsten2015 / Monika Vilémová, Jiří Matějíček, Barbara Nevrlá, Maryna Chernyshova, Pawel Gasior, et al.
-
Thermal Performance as the Main Factor of Energy Saving of Buildings in Russia
Abstract In this paper definitions of the concept of reduced resistance to heat transfer of the fragment of enclosing structure are formulated. Element approach for calculation of the reduced resistance's to heat transfer values of the fragment of...
2016 / Vladimir G. Gagarin -
Alloying Element Nitride Development in Ferritic Fe-Based Materials Upon Nitriding: A Review2016 / T. Steiner, E. J. Mittemeijer
-
Analysis of Abrasion Mechanisms in the AISI 303 Stainless Steel: Effect of Deformed Layer
Abstract Austenitic stainless steel is used in many industrial applications, especially those in which the corrosion resistance is relevant. However, this material is susceptible to surface damage, as well as the occurrence of phase transformations...
2016 / V. Seriacopi, N.K. Fukumasu, R.M. Souza, I.F. Machado -
Simulation of Forward Osmosis Using CFD
Abstract If fresh water and salt water are separated by a membrane, the fresh water would flow across the membrane from fresh water chamber to salt water chamber in a forward osmosis process. Forward osmosis and reverse osmosis processes have been...
2016 / Shyama Pankaj, N. Sajikumar, Roopesh Kaimal -
Application of Phase Change Materials to Reduce Heat Related Risks During Extreme Heat Waves in Australian Dwellings
Abstract This study investigates the effect of phase change materials (PCMs) in reducing potential heat stress risks in non-air-conditioned buildings during heat wave periods, such as that occurred in Melbourne, 2009. A residential house is...
2016 / Sayanthan Ramakrishnan, Xiaoming Wang, Jay Sanjayan, John Wilson -
Design and Construction of an Open-circuit Wind Tunnel with Specific Measurement Equipment for Cycling
Abstract In order to overcome resistance a cyclist has to deliver a total power output of which 90% is necessary to overcome the aerodynamic drag [1,2]. In order to perform research in this aerodynamic drag a wind tunnel has been built by the...
2016 / Bert Celis, Harm H. Ubbens -
Workpiece Surface Integrity when Milling Udimet 720 Superalloy
Abstract The paper details a comprehensive investigation into the surface integrity of Udimet 720 following end milling under different environment conditions (dry, flood, higher pressure and MQL) and cutting speed (25 and 50m/min). Surface...
2016 / R. Hood, J. Morris, S.L. Soo