Materials engineering topic list of research papers
-
A ‘Design for Energy Minimization’ approach to reduce energy consumption during the manufacturing phase
Abstract The combustion of fossil fuels for energy generation has contributed considerably to the effects of climate change. In order to reduce fossil fuel consumption, designers are increasingly seeking to reduce the energy consumption of products...
2016 / Yingying Seow, Nicholas Goffin, Shahin Rahimifard, Elliot Woolley -
Condition monitoring of face milling tool using K-star algorithm and histogram features of vibration signal
Abstract This paper deals with the fault diagnosis of the face milling tool based on machine learning approach using histogram features and K-star algorithm technique. Vibration signals of the milling tool under healthy and different fault...
2016 / C.K. Madhusudana, Hemantha Kumar, S. Narendranath -
Synthesis of superconducting Nb 3 Sn coatings on Nb substrates2015 / E Barzi, M Bestetti, F Reginato, D Turrioni, S Franz
-
Validation of a cyclic plasticity computational method using fatigue full-field deformation measurements2016 / J. Cuadra, K. P. Baxevanakis, A. Loghin, A. Kontsos
-
The Self-cleaning and Photocatalytic Properties of TiO2 Doped with SnO2 Thin Films Preparation by Sol-gel Method
Abstract In this study, TiO2 doped with SnO2 thin films were preparaed by the sol-gel method. The thin films were deposited onto glass substrate and calcinations at the temperature of 700°C for 2h with the heating rate of 10°C/min. Doping...
2016 / Weerachai Sangchay -
Structural Design Elements in Biological Materials: Application to Bioinspiration2015 / Steven E. Naleway, Michael M. Porter, Joanna McKittrick, Marc A. Meyers
-
Nonlinear Frequencies and Unbalanced Response Analysis of High Speed Rotor-Bearing Systems
Abstract This paper describes a step forward in calculating the nonlinear frequencies and resultant dynamic behavior of high speed rotor bearing system with mass unbalance. Nonlinear strongly coupled equations of motion has been formulated based on...
2016 / Phadatare H.P., Barun Pratiher -
Residual Stress Modeling in Electric Discharge Machining (EDM) by Incorporating Massive Random Discharges
Abstract EDM induced residual stress is a great concern for product performance. Current modeling methods of EDM are limited to a single discharge. However, a single discharge simulation is far from the reality to predict the residual stress due to...
2016 / J.F. Liu, Y.B. Guo -
A Risk Analysis for Asset Management Considering Climate Change
Abstract This paper presents an optimization framework for highway infrastructure elements that integrates risk profiles (for infrastructures) and economic aspects. One main goal is to assess the necessary additional effort to satisfy performance...
2016 / André D. Orcesi, Hélène Chemineau, Pei-Hui Lin, Pieter van Gelder, Noël van Erp -
Structural and mechanical defects of materials of offshore and onshore main gas pipelines after long-term operation2015 / Pavlo Maruschak, Sergey Panin, Iryna Danyliuk, Lyubomyr Poberezhnyi, Taras Pyrig, et al.
-
Studies of the AA2519 Alloy Hot Rolling Process and Cladding with EN AW-1050A Alloy2016 / B. Płonka, M. Rajda, Z. Zamkotowicz, J. Żelechowski, K. Remsak, et al.
-
Evolution of the Requirements for Anticorrosion Protection of Road and Bridge Infrastructure
Abstract Many industries all over the world have special, sector-specific requirements concerning anti-corrosion protection. This contributes to large savings in corrosion-related costs, which account for about 6% of the Gross Domestic Product in...
2016 / Agnieszka Królikowska, Łukasz Augustyński -
Semiactive Control of Earthquake/Wind Excited Buildings Using Output Feedback
Abstract Output feedback control using Magnetorheological dampers and Variable Stiffness Tuned Mass Dampers is considered. Firstly, seismic response control of a building with MR dampers is considered. Optimal Static Output Feedback (OSOF) control...
2016 / Naresh K. Chandiramani -
First-order correction to counter the effect of eccentricity on the hole-drilling integral method with strain-gage rosettes2016 / M. Barsanti, M. Beghini, L. Bertini, B. D. Monelli, C. Santus
-
Three-component U-Pu-Th fuel for plutonium irradiation in heavy water reactors2016 / Ross Peel, Luc Van Den Durpel, Mark Daniel Ogden, Karl Rhys Whittle
-
Spherical indentation of porous ceramics: Cracking and toughness
Abstract A combined experimental-numerical approach is used to characterise the fracture of a porous bulk ceramic material (La0.6Sr0.4Co0.2Fe0.8O3) with porosities of 5–45%, undergoing spherical indentation. The Gurson model was used in FEM to...
2016 / Zhangwei Chen, Xin Wang, Alan Atkinson, Nigel Brandon -
Railway Bridge Weigh-in-Motion System
Abstract The paper provides an overview of the development of a railway bridge weigh-in-motion (B-WIM) system, one of the first of its kind for weighing trains in motion. A steel truss bridge in Poland was used for testing the system. Four trains...
2016 / Aleš Žnidarič, Jan Kalin, Maja Kreslin, Peter Favai, Przemyslaw Kolakowski -
Increasing the Performance of EDM Process Using Tool Rotation Methodology for Machining AISI D3 Steel
Abstract Electric Discharge Machining is one of the most accurate unconventional manufacturing processes used for cutting or creating intricate shapes in very hard or difficult-to-cut, electrically conducting materials. The adoption of tool rotation ...
2016 / Anand Prakash Dwivedi, Sounak Kumar Choudhury -
An experimental study of a circular cylinder's two-degree-of-freedom motion induced by vortex2016 / Shin-Woong Kim, Seung-Jae Lee, Cheol-Young Park, Donghoon Kang
-
Thermal Performance Analysis of Combined Heating of Phase Change Kang and Firewall for Village Room under Winter Condition
Abstract Improving energy-saving performance and the indoor thermal environment of village room has become a social hot issues. This paper presented a kind of new encapsulation way of packaging 48 # paraffin phase change material in the structure of ...
2016 / Guohui Feng, Xing Sheng, Xiaolong Xu