Materials engineering topic list of research papers
-
Nanostructure Formations and Improvement in Corrosion Resistance of Steels by Means of Pulsed Electron Beam Surface Treatment2013 / K. M. Zhang, J. X. Zou, T. Grosdidier
-
Project Overview of HTS Magnet for Ultra-high-field MRI System
Abstract A project to develop an ultra-high-field magnetic resonance imaging (MRI) system based on HTS magnets using (RE)Ba2Cu3O7 (REBCO; RE=rear earth) coils is underway. The project is supported by the Japanese Ministry of Economy, Trade and...
2015 / Taizo Tosaka, Hiroshi Miyazaki, Sadanori Iwai, Yasumi Otani, Masahiko Takahashi, et al. -
Cation distribution and magnetization of BaFe12−2xCoxSnxO19 (x=0.9,1.28) single crystals2002 / Felip Sandiumenge, Benjamín Martínez, Xavier Batlle, Salvador Galí, Xavier Obradors
-
Solution processible organic transistors and circuits based on a C[sub 70] methanofullerene2005 / Thomas D. Anthopoulos, Dago M. de Leeuw, Eugenio Cantatore, Patrick van ’t Hof, Jan Alma, et al.
-
Study of the Surface Damage of Glass Reflectors Used in Concentrated Solar Power Plants
Abstract Solar mirrors are exposed, during their operation in Concentrated Solar Power plants –CSP-, to climatic stress factors that cause their degradation and therefore a decrease in the global efficiency of the plant. Sandstorms are among...
2015 / M. Karim, S. Naamane, C. Delord, A. Bennouna -
A Study on Temperature Distribution, Efficiency and Effectiveness of Longitudinal Porous Fins by Using Adomian Decomposition Sumudu Transform Method
Abstract In this paper, we studied the variation of temperature distribution, efficiency and effectiveness of porous fin for different fractional order α, porous parameter ξ and convection parameter δ by using Adomian Decomposition Sumudu Transform...
2015 / Trushit Patel, Ramakanta Meher -
Mechanical Properties and Fractographic Analysis of High Manganese Steels After Dynamic Deformation Tests2014 / M.B. Jabłońska
-
Optimal speed of hypersonic cruise flight
Abstract A coupling frame of speed gain and maintain was suggested to assess the flight performance of hypersonic cruise vehicles (HCV). The optimal cruise speed was obtained by analyzing the flight performance measured by the ratio of initial boost ...
2011 / Jing Fan -
Cool Down Analysis of a Cryocooler Based Quadrupole Magnet Cryostat
Abstract A superconducting quadrupole doublet magnet with cold superferric iron cover for the Hybrid Recoil Mass Analyzer (HYRA) beam line has been commissioned. The total cold mass of the helium vessel with iron yoke and pole is 2 ton. A set of two ...
2015 / A. Choudhury, S. Kar, J. Chacko, M. Kumar, S. Babu, et al. -
Failure analysis of a half-shaft of a Formula SAE Racing car
Abstract The formula SAE is a competition among students worldwide, where they are challenged to design, build and test a small formula-type racing car, following rules and specifications defined by the Society of Automotive Engineers (SAE). In the...
2016 / A.V. Guimaraes, P.C. Brasileiro, G.C. Giovanni, L.R.O. Costa, L.S. Araujo -
Probing carrier lifetimes in photovoltaic materials using subsurface two-photon microscopy2013 / Edward S. Barnard, Eric T. Hoke, Stephen T. Connor, James R. Groves, Tevye Kuykendall, et al.
-
Dry Sliding Wear Behavior of SiC Reinforced Titania Coating Deposited by High Velocity Oxy Fuel Spraying
Abstract The Conventional Titania (TiO2) and Titania blends with 10% SiC powder was thermally sprayed on commercially pure titanium substrate using High Velocity Oxy-Fuel (HVOF) spraying. The microhardness value of these coatings was measured by...
2014 / R. Sathiyamoorthy, K. Shanmugam, V. Balasubramanian -
Determination of Tool Wear in Turning Process Using Undecimated Wavelet Transform and Textural Features
Abstract The state of a cutting tool is a critical factor in any metal cutting process because dull or damaged cutting tool reduces surface quality and dimensional accuracy of workpiece and damages the machine tool. This paper proposes a novel...
2015 / Mahdi Danesh, Khalil Khalili -
Modeling of Mechanical Properties of Concrete Mixed with Expansive Additive2015 / Hyeonggil Choi, Takafumi Noguchi
-
First-sharp diffraction peaks in amorphous GeTe and Ge2Sb2Te5 films prepared by vacuum-thermal deposition2012 / Toshihiro Nakaoka, Hiroki Satoh, Saori Honjo, Hideo Takeuchi
-
Risks to the Hearing of Musicians – Subjective and Objective Evaluation of Sound Exposures in a Non-Professional Orchestra
Abstract While risks to the hearing of professional musicians were part of several studies in recent years, little attention was paid to the sound pressure exposure faced by amateur musicians. Thus, around 500,000 amateur musicians in Germany are...
2015 / Mario Penzkofer, Florian Finé, Karsten Kluth -
Light-Intensity-Induced Characterization of Elastic Constants and d33 Piezoelectric Coefficient of PLZT Single Fiber Based Transducers2013 / Lucjan Kozielski, Jiri Erhart, Frank Clemens
-
A review of friction stir welding of aluminium matrix composites
Abstract As a solid state joining process, friction stir welding (FSW) has proven to be a promising approach for joining aluminium matrix composites (AMCs). However, challenges still remain in using FSW to join AMCs even with considerable progress...
2015 / Omar S. Salih, Hengan Ou, W. Sun, D.G. McCartney -
Effect of annealing on properties of Mg doped Zn-ferrite nanoparticles
Abstract A comparison of structural and magnetic properties of as-prepared and annealed (900°C) Mg doped Zn ferrite nanoparticles (Zn1−x Mg x Fe2O4, with x=0, 0.1, 0.2, 0.3, 0.4 and...
2015 / K. Nadeem, S. Rahman, M. Mumtaz -
Effect of Angle between the Primary and Auxiliary Holes of an Anti-vortex Film Cooling Hole
Abstract In this paper, weanalytically investigated the effect of the angle between primary and auxiliary film cooling holes of an anti-vortex hole on the film cooling effectiveness. The effect of blowing ratio and the mainstream turbulence...
2015 / Younggi Moon, Soon Sang Park, Jung Shin Park, Jae Su Kwak