Materials engineering topic list of research papers
-
Effect of austenite stability on the low cycle fatigue behavior and microstructure of high alloyed metastable austenitic cast TRIPsteels
Abstract Room-temperature total strain controlled low-cycle fatigue tests were carried out on two types of high alloyed metastable austenitic cast TRIP steels with different chemical compositions resulting in different austenite stabilities. The...
2010 / A. Glage, A. Weidner, H. Biermann -
An improved attribute reduction algorithm based on importance of attribute value
Abstract The theory of rough set is a new mathematical tool to deal with the uncertain problems, and the attribute reduction is one of key problems in the theory. To obtain a better method of attributes reduction in decision-making system, a concept ...
2010 / Ju Li, Xiaowen Fan, Xing Wang -
Fabrication Processing and Evaluation on Thermal Shock Damage of C/SiC Composite
Abstract Carbon fiber reinforced SiC matrix composites (C/SiC) is one of attractive candidates in the ultrahigh temperature components such as turbine rotor and internal combustion part. The objective of this paper is to investigate the...
2011 / Jin Kyung Lee, Sang Pill Lee, Joon Hyung Byun, Dong Soo Bae -
Effect of surface residual stress and inclusion size on fatigue failure mode of matrix HSS in very high cycle regime
Abstract Fatigue properties in high cycle and very high cycle fatigue regime of matrix high-speed tool steel (1.3C-6W-5Mo-3V-8Co) were investigated through the experimental results obtained from a cantilever-type rotary bending fatigue test in air...
2010 / Yuuji Shimatani, Kazuaki Shiozawa, Takehiro Nakada, Takashi Yoshimoto -
Fatigue fracture behavior of Ti-6Al-4V PVD coated
Abstract Fatigue, corrosion and wear resistance are important parameters in aircraft components development as landing gear. High strength/weight ratio and effective corrosion resistance make of titanium alloys an alternative choice to replace steel ...
2010 / Midori Yoshikawa Pitanga Costa, Maria Odila Hilário Cioffi, Marcelo Lima Rossignolo Venditti, Herman Jacobus Cornelis Voorwald -
Experimental and Numerical Study of Expanded Aluminum and Steel Tubes
Abstract This paper presents the design of an experimental set-up to mechanically expand aluminum and steel tubes using conical hardened steel mandrels. The experimental study considered four radial expansion ratios of 10, 15, 20 and 25% and three...
2011 / A.C. Seibi, I. Barsoum, A. Molki -
Mechanical behaviour of polypropylene reinforced sugarcane bagasse fibers composites
Abstract Recently the interest in composite materials reinforced with natural fibers has considerably increased due to the new environmental legislation as well as consumer pressure that forced manufacturing industries to search substitutes for the...
2011 / E.F. Cerqueira, C.A.R.P. Baptista, D.R. Mulinari -
Coupled multi-disciplinary methods for structural reliability and affordability
Abstract A computational simulation method is presented for Non-Deterministic Multidisciplinary Optimization of engine composite materials and structures. A hypothetical engine duct made with ceramic matrix composites (CMC) is evaluated...
2011 / Christos C. Chamis -
Microstructure evaluation and crack initiation crack for AZ31 sheet under biaxial stress
Abstract In this study, a biaxial tensile test of cruciform specimens containing centre notch was conducted with a miniature biaxial tensile test system in order to clarify the deformation behavior near the crack tip at the early stages of crack...
2011 / Jiangang Wang, Dongying Ju, Fuxing Yin, Hongyang Zhao -
Advanced simulation tool for the design of sensors and actuators
Abstract Sensors, actuators, and sensor-actuator systems are often based on the mutual interaction of physical fields, e.g., the mechanical field with the electromagnetic field. The accurate modeling of such transducers leads to so-called...
2010 / M. Kaltenbacher -
Influence of strain rate on P92 microstructural stability during fatigue tests at high temperature
Abstract 9-12%Cr creep-resistant ferritic-martensitic steels are candidates for structural components of Generation IV nuclear power plants. However, they are sensitive to softening during fatigue and creep-fatigue loading. To better understand...
2010 / P.F. Giroux, F. Dalle, M. Sauzay, C. Caës, B. Fournier, et al. -
Novel Multi Optical Trapping Tool Generation within Add/Drop Filter System Controlled by Light
Abstract We propose a novel system of multi optical trapping tool using a bright soliton pulses propagating within the add/drop optical filter system. The multiplexing signals with different wavelengths of the bright solition are controlled and...
2011 / Phichai Youplao, Somsak Mitatha, Preecha Yupapin -
Essential Aspects of Beach Erosion - Lessons from Devastation of Ichinomiya Coast, Japan
Abstract The fundamental issues of the beach erosion including the difficulty in social and comprehensive adjustments of the beach erosion were discussed through a case study, taking the Ichinomiya coast on south Kujukuri Beach as an example. On...
2015 / Satoquo Seino, Takaaki Uda, Yasuro Ohtani, Yasuhiro Ohki -
Designing License Plate Identification through Digital Images with OpenCV
Abstract The aim of this research is to design and analyze the License Plate Identification program mediated through Digital Images or Automatic Number Plate Recognition (ANPR), especially by using desktop peripheral. In doing so, license plates...
2015 / Abdillah Komarudin, Ahmad Teguh Satria, Wiedjaja Atmadja -
Fatigue Failure Analyses on a Ti-45Al-8Nb-0.2W-0.2B-0.1Y Alloy at Different Temperatures2012 / Xi-Shu Wang, Min Zhang, Xi-Ping Song, Su Jia, Qiang Chen, et al.
-
Safety Design and Evaluation in a Large-Scale Japan Sodium-Cooled Fast Reactor2012 / H. Yamano, S. Kubo, Y. Shimakawa, K. Fujita, T. Suzuki, et al.
-
Microstructural Evolution in Materials during Thermal Processing2012 / Joseph K. L. Lai, Brian Ralph, Zhiwen Chen, Kin Ho Lo
-
Nanovectorized radiotherapy: a new strategy to induce anti-tumor immunity2012 / Claire Vanpouille-Box, François Hindré
-
Internal Friction on AISI 304 Stainless Steels with Low Tensile Deformations at Temperatures between − 50 and 20 C2010 / T. F. A. Santos, M. S. Andrade
-
Dendritic Cells The Tumor Microenvironment and the Challenges for an Effective Antitumor Vaccination2012 / Fabian Benencia, Leslee Sprague, John McGinty, Michelle Pate, Maria Muccioli