Mechanical engineering topic list of research papers
-
The Judgment of Electronic Diesel Engine State
Abstract The paper analyzed a electronic diesel engine‘s working state according to the engine speed and load condition, and compiled the control procedure using the MATLAB / Simulink / Stateflow software. According to the engine speed, load and...
2012 / Jinhu Wang, Tingting Cheng -
Study on Repetitive PID Control of Linear Motor in Wafer Stage of Lithography
Abstract A ‘Repetitive + PID + feedforward’ control mode is proposed to improve the trajectory-tracking performance of linear motors in wafer stage of lithography. The positioning error of linear motor is decreased greatly compared to PID control...
2012 / Bo-jie Hou, Jian-she Gao, Xiao-qing Li, Yun-fei Zhou -
Trajectory control strategy of cathodes in blisk electrochemical machining
Abstract A turbine blisk, which combines blades and a disk together, is one of the most important components of an aero engine. In the process of blisk electrochemical machining (ECM), the sheet cathode, which is usually used as a tool electrode,...
2013 / Dong Zhu, Di Zhu, Zhengyang Xu, Laishui Zhou -
Study on the Reform and Mode of Local Higher Fashion Design and Engineering Education Which Service Industry Development
Abstract This article is based on the relationship between development of creative industry and regional demand of talent structure in Shanghai and analysis the mode of Institute of fashion education in Shanghai University of Engineering Science...
2012 / Shouzhong Hu, bingqiang Tian -
Method of Aircraft Fuel Tank System Ignition Source Fail-Safe Feature Analysis
Abstract Fuel tank system ignition source failure threatens the safety of the aircraft. For different possible ignition sources in and around the fuel tank system and their airworthiness requirements, this paper proposes a particular method using...
2011 / Zhang Yanjun, Sun Youchao, Wang Fengchan, Zeng Haijun -
Analysis of Cable-actuated Parallel Robot with Variable Length and Velocity cable
Abstract This paper is concerned with modeling, analysis of cable-actuated robotic manipulators with non-negligible cable mass and velocity. The manipulator architecture is a simplified version adopted from the structure of the Feed cabin to track...
2011 / Q.J. Duan, X.C. Duan -
Thrust Reverser Optimization for Safety with CFD
Abstract With its function of decreasing the ground roll distance, thrust reverser (T/R) may cause safety problems in case of its inadequate integration with the aircraft. Traditionally, designers rely on wind tunnel testing, which is expensive and...
2011 / Qian Ruizhan, Zhu Ziqiang, Duan Zhuoyi -
Hydraulic drive test platform of automatic underwater welding
Abstract Because welding repair of nuclear power plant at the underwater environment, in order to simplify the sealing and increase the safety of test equipment, hydraulic drive automatic welding platform was designed that provides the relative...
2011 / Jialei Zhu, Xiangdong Jiao, Canfeng Zhou -
Supporting Multidisciplinary Vehicle Analysis Using a Vehicle Reference Architecture Model in SysML
Abstract To develop competitive vehicles with ever increasing complexity, automotive designers need to improve their ability to explore a broad range of system architectures efficiently and effectively. Whereas traditional vehicle systems are based...
2013 / Jaclyn M. Branscomb, Christiaan J.J. Paredis, Judy Che, Mark J. Jennings -
Application of Flow Control Techniques for Indoor Ventilation
Abstract Significant amount of energy is consumed each year on heating, ventilating and air conditioning (HVAC), raising ongoing demand for energy efficient HVAC systems. This study explores the applicability of flow control techniques to improve...
2012 / Chaofan Wu, Noor-E-Alam Ahmed -
Investigating Micro Spherical Stylus Tips Fabrication by Electro Chemical and Single Pulse Electro Discharge Processes
Abstract M icro spherical stylus tip plays an important role in micro coordinate measuring machine (CMM) metrology. A micro CM M needs a tiny spherical stylus tip with diameter less than 0.125mm to measure micro components such as micro slots, micro ...
2013 / C.-F. Tsai, C.-C. Cheng, D.-Y. Sheu -
Load Allocation and Equilibrium for Planetary Gear Reducers of Earth-Pressure-Balance Shield Machine
Abstract To optimize the 3-stages planetary gear reducer (PGR) in the Earth-Pressure-Balance Shield Machine (EPBSM), it is necessary to firstly define the EPBSM environment. The needed torque of the cutter-head, therefore, is analyzed when the EPBSM ...
2012 / Zhang Ganqing -
A Software Tool for the Design of Critical Robot Missions with Performance Guarantees
Abstract Deploying a robot as part of a counter-weapons of mass destruction mission demands that the robotic software operates with high assurance. A unique feature of robotic software development is the need to perform predictably in a physical...
2013 / D.M. Lyons, R.C. Arkin, P. Nirmal, S. Jiang, T.-M. Liu -
Numerical Analysis of Temperature Field in a Disc Brake at Different Cover Angle of the Pad2015 / Piotr Grześ
-
Nonlinear effects on motions and loads using an iterative time-frequency solver2015 / D. Bruzzone, C. Gironi, A. Grasso
-
Trade-off between maximum cardinality of collision sets and accuracy of RFID reader-to-reader collision detection2013 / Linchao Zhang, Filippo Gandino, Renato Ferrero, Bartolomeo Montrucchio, Maurizio Rebaudengo
-
Factor Analysis of the Aggregated Electric Vehicle Load Based on Data Mining2012 / Qinglai Guo, Yao Wang, Hongbin Sun, Zhengshuo Li, Shujun Xin, et al.
-
The Design of RFID Conveyor Belt Gate Systems Using an Antenna Control Unit2011 / Chong Ryol Park, Seung Joon Lee, Ki Hwan Eom
-
Design and Analysis of Impedance Pumps Utilizing Electromagnetic Actuation2010 / Yu-Hisang Wang, Yao-Wen Tsai, Chien-Hsiung Tsai, Chia-Yen Lee, Lung-Ming Fu
-
A Virtual Tool for Minimum Cost Design of a Wind Turbine Tower with Ring Stiffeners2013 / Fatih Karpat