Mechanical engineering topic list of research papers
-
Experiment and Simulation Investigation on the Tensile Behavior of Composite Laminate with Stitching Reinforcement2011 / Yi Wang, Nai Xian Hou, Zhu Feng Yue
-
Carbon dioxide refrigeration with heat recovery for supermarkets2012 / I. Colombo, G. G. Maidment, I. Chaer, J. M. Missenden
-
Large Eddy Simulation of Pulsating Flow before and after CoA Repair: CFD for Intervention Planning2015 / R. Gardhagen, F. Carlsson, M. Karlsson
-
The Role of Operational Factors in Shaping of Wear Properties of Alloyed Austempered Ductile Iron Part I. Experimental Studies Abrasive Wear of Austempered Ductile Iron (Adi) in the Presence of Loose Quartz Abrasive/ Rola Czynników Eksploatacyjnych W Kształtowaniu Właściwości Zużyciowych Stopowych Żeliw Sferoidalnych Ausferrytycznych Część I. Eksperymentalne Badania Zużycia Sciernego W Obecności Lużnego Scierniwa Kwarcowego Żeliw Adi2015 / A.N. Wieczorek
-
Behavior-Based Cleaning for Unreliable RFID Data Sets2012 / Hua Fan, Quanyuan Wu, Yisong Lin
-
Problems Encountered in Fluctuating Flame Temperature Measurements by Thermocouple2008 / Nadir Yilmaz, Walt Gill, A. Burl Donaldson, Ralph E. Lucero
-
A Micro-Force Sensor with Slotted-Quad-Beam Structure for Measuring the Friction in MEMS Bearings2013 / Huan Liu, Shuming Yang, Yulong Zhao, Zhuangde Jiang, Yan Liu, et al.
-
Finite element method study on the influence of initial stress on machining process2015 / Y. Ma, D. Yu, P. Feng, Z. Wu, J. Zhang
-
Influence of compression ratio on combustion and performance characteristics of direct injection compression ignition engine
Abstract The importance of diesel engines for human application is growing day by day. The engine operating parameters also play a key role in tuning the engine conforming to the better performance and emission standards. The effect of varying the...
2015 / V. Hariram, R. Vagesh Shangar -
Experimental determination of correlations for mean heat transfer coefficients in plate fin and tube heat exchangers2013 / Dawid Taler
-
A study on an efficient prediction of welding deformation for T-joint laser welding of sandwich panel Part II : Proposal of a method to use shell element model2015 / Jae Woong Kim, Beom Seon Jang, Sung Wook Kang
-
Extension of the resistance, inductance, capacitance electrical circuit to fractional derivative without singular kernel2015 / A. Atangana, B. S. T. Alkahtani
-
A Survey on Occurrence of Critical Machines in a Manufacturing Environment
Abstract The modern manufacturing environment is generally expressed in terms of flowshop, where all the machines are considered equally, despite the availability of critical machines. Here, a survey was made on the manufacturing environment to...
2014 / R. Pugazhenthi, M. Anthony Xavior -
An Experimental and Numerical Investigation of the Performance, Combustion and Emission Characteristics of a Diesel Engine Fueled with Jatropha Biodiesel
Abstract The effect of addition of jatropha biodiesel to mineral diesel on the performance and emission characteristics of a conventional compression ignition engine have been experimentally investigated and compared with simulated data using...
2014 / Gaurav Paul, Ambarish Datta, Bijan Kumar Mandal -
Ducted Propeller Flow Analysis by Means of a Generalized Actuator Disk Model
Abstract The paper presents a generalized semi-analytical actuator disk model as applied to the analysis of the flow around ducted propellers at different operating conditions. The model strongly couples the non-linear actuator disk method of...
2014 / Rodolfo Bontempo, Massimo Cardone, Marcello Manna, Giovanni Vorraro -
Inhibition of the Premixed CH4/Air Deflagration by Powdered Extinguishing Agents
Abstract In order to improve the utilization rate of extracted coal-bed methane, effective safety measures for low concentration gas transmission line must be provided. In this work, suppression of gas explosion in a channel by powdered...
2014 / Li-gang Zheng, Kai Zheng, Rong-kun Pan, Ming-gao Yu, Hao You, et al. -
A Tolerance Analysis Method for Rotating Machinery
Abstract Rotating machinery is widely used in many fields of engineering. In rotating machinery design, the rotary precision is usually the first issue to determinate. Rotary precision is affected by many factors, such as tolerance design, assembly...
2013 / Junkang Guo, Jun Hong, Zhaohui Yang, Yong Wang -
Resource-efficient Ball Screw by Adaptive Lubrication
Abstract In this paper, the development of a methodology for reducing the energy demand and increasing the life time of ball screws by minimizing the friction torque with adaptive lubrication of the ball screw nut is presented. ...
2014 / J. Fleischer, U. Leberle, J. Maier, A. Spohrer -
Author Index2011 /
-
Thermal analysis and modeling of surface heat exchangers operating in the transonic regime
Abstract Surface coolers for tightly packed airbreathing propulsion are proposed to evacuate the heat loads from the lubrication circuit. This paper demonstrates the capability of integrated bypass-flow surface heat exchangers to cope with the high...
2013 / J. Sousa, L. Villafañe, G. Paniagua