Mechanical engineering topic list of research papers
-
Evaluation of Seismic Behaviors of Partially Deteriorated Reinforced Concrete Circular Columns Retrofitted with CFRP2014 / Dongxu Hou, Jianyun Pan, Xinglang Fan, Zhimin Wu, Prosper Marindiko
-
Crack Extension Resistance of Normal-Strength Concrete Subjected to Elevated Temperatures2014 / Jing Chen, Zhoudao Lu
-
Day-to-Day Scheduling Travel Time Adjustment Behavior and Simulation2014 / Hua-Min Li, David Z. W. Wang, Hai-Jun Huang, Xiao-Jun Yu
-
Corner-milling of Thin Walled Cavities on Aeronautical Components
Abstract This article presents a mathematical model of helical end-milling forces through experimental identification of the cutting coefficients and analyzes the changes of corner-milling forces under different conditions. In allusion to the...
2009 / Wu Qiong, Zhang Yidu, Zhang Hongwei -
Winding Pattern Design and Simulation of S-elbow
Abstract Aimed at the S-elbow composed of two elbows with different radii, this article proposes a winding pattern design method combined with patch winding method and traditional winding method. It proposes an optimal combination of calculating the ...
2010 / Wang Xianfeng, Xiao Jun, Wen Liwei -
Conjugate Calculation of Gas Turbine Vanes Cooled with Leading Edge Films
Abstract Conjugate calculation methodology is used to simulate the C3X gas turbine vanes cooled with leading edge films of “shower-head” type. By comparing calculated results of different turbulence models with the measured data, it is clear that...
2009 / Ping Dong, Qiang Wang, Zhaoyuan Guo, Hongyan Huang, Guotai Feng -
Coupled Heat Transfer Simulation of a High-pressure Turbine Nozzle Guide Vane
Abstract The investigation is intended to verify a coupled solver developed for turbines to illustrate how transition exerts effects on the predicted thermal loads. The solver couples the N-S solver named HIT-3D, with a thermal conduction module...
2009 / Wang Qiang, Guo Zhaoyuan, Zhou Chi, Feng Guotai, Wang Zhongqi -
A generalized mathematical model to determine the turning movement counts at roundabouts
Abstract Traffic turning movement counts at roundabouts is one of the key inputs required for roundabout assessment, control and management. Traditionally, a direct counting is conducted to track a vehicle from entering through circulation until...
2014 / Al-Sayed Ahmed Al-Sobky, Ibrahim Hassan Hashim -
Variable speed wind turbine for maximum power capture using adaptive fuzzy integral sliding mode control2014 / Saravanakumar Rajendran, Debashisha Jena
-
Effects of Machine Tool Configuration on Its Dynamics Based on Orthogonal Experiment Method
Abstract In order to analyze the influence of configuration parameters on dynamic characteristics of machine tools in the working space, the configuration parameters have been suggested based on the orthogonal experiment method. Dynamic analysis of...
2012 / Xiangsheng GAO, Yidu ZHANG, Hongwei ZHANG, Qiong WU -
Mathematical Modelling and Simulation of the Behaviour of the Steam Turbine
Abstract Model simulations are becoming very important in dynamic power system analyses. However, no mathematical system can exactly model a physical process. Based on mathematical models of the processes and design calculations, PC programs allow...
2014 / Mircea Dulau, Dorin Bica -
A Capacity Assessment Method on Urban Expressway after Traffic Incident
Abstract To explore the urban expressway's capacity after a traffic incident, a capacity assessment approach based on VISSIM has been proposed, in which we disassemble the evolutionary processes of local traffic state after traffic incident and...
2013 / Chen Hong, You Yue-sheng, Zhang Bin -
The Technology of Mould Steel for Online Pre-hardening
Abstract This article describes a production method of mould steel pre-hardening, and focus on the advantage of this method, The technical core of method is the variable frequency and variable amplitude pulse uniform high-precision temperature...
2014 / Dongmei Zhu, Guoyong Liu, Mouwei Li, Shaojun Zhang, Xinxiao Bian, et al. -
Non-adiabatic flow characteristics of micro impeller
Abstract Non-adiabatic working condition is one of the major causes of performance deterioration in micro gas turbine engines. Complex micro scale geometry, low Reynolds number operating condition and high surface to volume ratio all lead to severe...
2014 / Qianwei Sun, Qiushi Li, Ali Arshad, Zhiping Li -
Deploying process modeling and attitude control of a satellite with a large deployable antenna
Abstract Modeling and attitude control methods for a satellite with a large deployable antenna are studied in the present paper. Firstly, for reducing the model dimension, three dynamic models for the deploying process are developed, which are built ...
2014 / Zhigang Xing, Gangtie Zheng -
Selective laser melting (SLM) and topology optimization for lighter aerospace componentes
Abstract Additive Manufacturing (AM) is a manufacturing process through which a 3D component is produced by consecutively adding material. One of the most promising AM processes is SLM. In SLM a laser completely melts metallic powder particles...
2016 / Miguel Seabra, José Azevedo, Aurélio Araújo, Luís Reis, Elodie Pinto, et al. -
Evaluation of Mechanically and Adhesively Fixed External Insulation Systems Using Vacuum Insulation Panels for High-Rise Apartment Buildings2014 / Sihyun Park, Bo-Hye Choi, Jae-Han Lim, Seung-Yeong Song
-
A Comparison of Ethanol and Methanol Blending with Gasoline Using a 1-D Engine Model
Abstract The world's fossil fuel reserves are limited and there has been intensive research to find out alternatives to fossil fuels. Hence, there is a progressive interest related to using non-fossil sources in vehicles. The biofuel is a major...
2015 / Simeon Iliev -
A High Performance Computing Approach to the Simulation of Fluid-Solid interaction Problems with Rigid and Flexible Components2014 / Arman Pazouki, Radu Serban, Dan Negrut
-
Thermodynamic Analysis of a Ship Power Plant Operating with Waste Heat Recovery through Combined Heat and Power Production2014 / Mirko Grljušić, Vladimir Medica, Nikola Račić