Mechanical engineering topic list of research papers
-
Improvement on Transportation Safety on Bus by Installing A Speed Limiter in Conventional Engine to Reduce Speed Rate2016 / Hadi Pranoto, A.M. Leman, Darwin Sebayang, D. Feriyanto
-
Turbulent flow computation in a circular U-Bend2014 / Abdelkrim Miloud, Mohammed Aounallah, Mustapha Belkadi, Lahouari Adjlout, Omar Imine, et al.
-
A Numerical Investigation of Fluid Flow Maldistribution in Inlet Header Configuration of Plate Fin Heat Exchanger
Abstract The common assumption made for the design of heat exchangers is that the fluid flow in the header and core part is uniform. It is found that the flow maldistribution is very significant in the direction normal to the flow direction in inlet ...
2016 / Appasaheb Raul, B.N. Bhasme, R.S. Maurya -
Determination of Active Personal Space Based on Emotion when Interacting with a Service Robot2013 / Sajal Chandra, Ashoke Kumar Sen Gupta, M. K., R. N.
-
Control of nonlinear state-dependent systems using a receding horizon strategy2016 / J. Wang
-
Design and Development of a Real-Time GPS-Aided SINU System2012 / Chot Hun, Tien Sze, Voon Chet
-
Thermal Rating of Overhead Insulation-Covered Conductors in the Steady-State Regime2016 / Stanislav Girshin, Vladimir Goryunov, Evgenii Kuznetsov, Elena Petrova, Anton Bubenchikov, et al.
-
Rheology of wet granular materials in shear flow: experiments and discrete simulations2016 / Michel Badetti, Abdoulaye Fall, Jean-Noël Roux
-
The Use of Noise Dampening Mats to Reduce Heavy-Equipment Noise Exposures in Construction
Abstract The performance of sound barriers was evaluated to determine their technical effectiveness and practicality in reducing noise exposures to operating engineers in construction. Commercially purchased sound dampening mats (SDMats) were...
2016 / Sabah Saleh, Susan Woskie, Anila Bello -
Productivity Progression with Tool Wear in Titanium Milling
Abstract This paper presents experimental results for flank wear width, cutting force, temperature, and surface finish with increasing tool wear in titanium (Ti6Al4V) milling. The variation in these process indicators is presented for repeated...
2016 / Joyson Menezes, Mark A. Rubeo, Kadir Kiran, Andrew Honeycutt, Tony L. Schmitz -
Damage detection method for sleepers based on vibration properties2015 / Kodai Matsuoka, Tsutomu Watanabe, Masamichi Sogabe
-
Whole-Body Motion Planning for Humanoid Robots by Specifying Via-Points2013 / ChangHyun Sung, Takahiro Kagawa, Yoji Uno
-
Kinematic Dexterity Maximization of an Omnidirectional Wheeled Mobile Robot: A Comparison of Metaheuristic and SQP Algorithms2012 / Miguel G., Carlos A., Jaime Alvarez-Gallegos, Edgar A.
-
Robot Control near Singularity and Joint Limit Using a Continuous Task Transition Algorithm2013 / Hyejin Han, Jaeheung Park
-
Compliance modeling of planar flexure-based mechanisms and its application to micro-motion stages2016 / Yunsong Du, Tiemin Li, Wei Ji, Yao Jiang, Fuhua Li
-
Research on the Cross-Coupling of a Two Axes Gimbal System with Dynamic Unbalance2013 / Maher Abdo, Ahmad Reza, Alireza Toloei, Mohammad Reza
-
Bond strength between carbon fiber-reinforced plastic tubes and aluminum joints for racing car suspension2016 / J. Wang, H. Gao, L. Ding, Y. Hao, B. Wang, et al.
-
Feasibility Study of an Extrusion-based Direct Metal Additive Manufacturing Technique
Abstract A new extrusion-based additive manufacturing technique is described in this paper together with the main components of the machine capable of carrying out the process. Innovative characteristics of the machine are the fixed extrusion head...
2016 / Massimiliano Annoni, Hermes Giberti, Matteo Strano -
Finding the Generalized Forces of a Series-Parallel Manipulator2013 / Mario Garcia-Murillo, Jaime Gallardo-Alvarado, Eduardo Castillo-Castane
-
Rotating Machinery Diagnostics Using Deep Learning on Orbit Plot Images
Abstract Although the orbit analysis (orbit shape and size) is commonly used to diagnose rotating machinery, the diagnosis heavily depends on the expert knowledge or experience due to the difficulties of extracting mathematical features for...
2016 / Haedong Jeong, Seungtae Park, Sunhee Woo, Seungchul Lee