Mechanical engineering topic list of research papers
-
Structure and performance study of ad hoc microsat constellation with secondary launches2016 / G. Xin, H. Bing, W. Yunhua
-
Dynamics of a high speed coned thrust bearing with a Navier slip boundary condition2015 / N. Y. Bailey, K. A. Cliffe, S. Hibberd, H. Power
-
Optimization design for turbodrill blades based on response surface method2016 / X. Zhang, S. Yu, Y. Gong, Y. Li
-
Effect of Gap Flow on the Torque for Blades in a Rim Driven Thruster without Axial Pressure Gradient
Abstract This paper applied RANS solver and angular momentum current analyzing method to study the effect of gap flow in a rim driven thruster on the torque of the blades when the propeller was replaced by a rotating disk. The rim's torque was...
2015 / Q.M. Cao, W.F. Zhao, D.H. Tang, F.W. Hong -
Numerical investigation of variable inlet guide vanes with trailing-edge dual slots to decrease the aerodynamic load on centrifugal compressor impeller2016 / J. Xin, X. Wang, H. Liu
-
Study on Universal Parameter of Power System for Urban Bus in Cold Region Based on Driving Cycles2015 / S.-w. Li, Z.-k. Yang, Z.-f. Yang, L.-k. Yang, Y. Xu, et al.
-
Evaluation of hydrodynamic forces on turbine ring gate during emergency shutdown process2015 / Z. Mo, J. Xiao, G. Wang
-
Wave Interaction with a Double Chamber Oscillating Water Column Device2013 / R. Wilbert, V. Sundar, S. Sannasiraj
-
Multi-objective Gaussian particle swarm algorithm optimization based on niche sorting for actuator design2015 / H. Liang, K. Zhang, J. You, H. Yu
-
Three-axes error modeling based on second order dual numbers2015 / Michal Holub, Jaroslav Hrdina, Petr Vašík, Jan Vetiška
-
Production Technology and a Design of Transfer Ports in a Cylinder of a Small-Volume Motorcycle
Abstract This work deals with the cylinder of the Jawa 50 Pioneer, which has come to the attention of the general public at the present time, primarily because this type of motorcycle is being increasingly used in races. First, it was necessary to...
2015 / Milan Daňa, Ivana Zetková, Václav Schorník -
A nth-order shear deformation theory for composite laminates in cylindrical bending2015 / A. S. Sayyad, Y. M. Ghugal
-
Heat transfer capability simulation of high-temperature heat pipe in supersonic vehicle leading edge applications2016 / D. Liu, Y. Liu
-
A torque compensation strategy in two-speed automated mechanical transmission shift process for pure electric vehicles2015 / J. Hu, C. Sun, J. Xiao, J. Li
-
The mechanical structure of mobile module for new self-configurable intelligent environment2015 / JongSeung Park, Toshitake Nunogaki, Joo-Ho Lee
-
Investigating the interaction between the parking choice and holiday travel behavior2015 / B. Wang, C. Shao, J. Li, D. Zhao, M. Meng
-
Optimal set-up and surface finish characteristics in electrical discharge machining on Ti-5Al-2.5Sn using graphite
Summary In electrical discharge machining (EDM) process which is an advance and non-conventional technique, the selection of machining parameters for achieving high machining performance is an important; however, very problematic task. In the...
2016 / Md. Ashikur Rahman Khan, M.M. Rahman, Zayed-Us-Salehina, Md. Saifur Rahman -
Investigating the Energy Consumption of the PECM Process for Consideration in the Selection of Manufacturing Process Chains
Abstract The initial planning of manufacturing process chains provides the opportunity to sustainably influence the energy requirement for the manufacturing of industrial products by selecting the process chain with the lowest energy consumption....
2015 / Martin Swat, Andreas Rebschläger, Kirsten Trapp, Tim Stock, Günther Seliger, et al. -
Analysis of Tradable Bottleneck Permits Scheme when Marginal Utility of Toll Cost Changes Among Drivers
Abstract This study proposes a Pareto improving congestion pricing using tradable bottleneck permits (TBP) scheme under the condition that marginal utility of toll cost changes among drivers. The TBP scheme is originally one of the first-best...
2015 / Katsuya Sakai, Takahiko Kusakabe, Yasuo Asakura -
Tool path planning and milling surface simulation for vehicle rear bumper mold2016 / P. Wang, S. Zhang, Z. Li, J. Li