Mechanical engineering topic list of research papers
-
Design for manufacturability in virtual environment using knowledge engineering2014 / Julian Jakubowski, Jozef Peterka
-
Design of Electrical/Mechanical Hybrid 4-Redundancy Brushless DC Torque Motor
Abstract This article presents a novel electrical/mechanical hybrid 4-redundancy brushless DC torque motor (BLDCM), which has found applications in direct drive actuators (DDA) of aerial vehicles. This motor is characteristic of...
2010 / Guo Hong, Wang Wei, Xing Wei, Li Yanming -
Drag Reduction for an Airship with Proper Arrangement of Propellers
Abstract In this article, the flow field around an airship with propellers blowing is calculated on the basis of the Reynolds-averaged Navier-Stokes equations with SST turbulent models. Modeled each as an actuator disk, the propellers are arranged...
2009 / Xie Fei, Ye Zhengyin -
Navigation Accuracy Category-Position Models and Estimate Position Uncertainty Calculations for TIS-B System
Abstract Navigation accuracy category-position (NACp) is an important parameter for system accuracy of traffic information service-broadcast (TIS-B), which is determined by estimate position uncertainty (EPU). Centered about the problems that the...
2009 / Zhang Qingzhu, Zhang Jun, Zhu Yanbo, Liu Wei -
Regenerative Instability of Impact-cutting Material Removal in the Grinding Process Performed by a Flexible Robot Arm
Abstract Robotic machining is emerging as a viable alternative for some conventional machining tasks. Nevertheless, a challenge to cutting performance remains: vibrational instability is reported to be more severe with robotic cutting due to robot...
2014 / Farzad Rafieian, Bruce Hazel, Zhaoheng Liu -
Nusselt Correlations in a Trailing Edge Cooling System with Long Pedestals and Ribs
Abstract Detailed TLC measurements have been carried out to estimate the heat transfer coefficient in stationary conditions under high Reynolds numbers in a trailing edge cooling system of a high pressure gas turbine blade. The investigated geometry ...
2014 / Ahmed Beniaiche, Carlo Carcasci, Marco Pievaroli, Adel Ghenaiet -
Experimental Research on the Ground Surface Quality of Creep Feed Ultrasonic Grinding Ceramics (Al2O3)
Abstract In order to grind the ceramic blade surface with the Numerical Control contour evolution ultrasonic grinding method using the simple shape grinding wheel, primary comparative experiments of creep feed grinding with and without ultrasonic...
2011 / Jian-xin ZHENG, Jia-wen XU -
Study on Nonlinear Coupling Wave Model for Liquid Droplet-Solid Impact
Abstract In order to investigate the material corrosion by liquid droplet-solid impact, a nonlinear coupling wave model adopted to analyze the impact between the spherical liquid droplet and an elastic solid plane has been developed. Many usable...
2011 / Di ZHANG, Yong-hui XIE -
Study on Machining Deformation of Aircraft Monolithic Component by FEM and Experiment
Abstract Machining deformation of aircraft monolithic component is simulated by finite element method (FEM) and validated by experiment. The initial residual stress in pre-stretched plate is generated by simulating quenching and stretching...
2011 / Hui-yue DONG, Ying-lin KE -
Using Computer Simulation and Animation to Improve Student Learning of Engineering Dynamics
Abstract This paper reports the longitudinal assessment results of an interactive computer simulation and animation (CSA) learning module that was developed for, and implemented in, an engineering dynamics course. Longitudinal assessments were...
2012 / Ning Fang -
The Effect of Evaluation Strategy and Music Performance Presentation Format on Score Variability of Music Students’ Performance Assessment
Abstract The present study aims to investigate the score variability of music performance evaluation according to two factors: the music performance presentation format (audio versus audio-visual presentation of students’ music performance) and the...
2014 / Dorina Iusca -
Generation of Accelerated Stability Experiment Profile of Inertial Platform Based on Finite Element
Abstract The residual stress generated in the manufacturing process of inertial platform causes the drift of inertial platform parameters in long-term storage condition. However, the existing temperature cycling experiment could not meet the...
2012 / Yunxia CHEN, Xiaokai HUANG, Rui KANG -
Design of a Network of Scalable Modular Manufacturing Systems to Support Geographically Distributed Production of Mass Customized Goods
Abstract In our globalized economic system, industrial production has to step outside the boundaries of individual enterprises and single production units [1]. The increasing globalisation, new models for growth and Internationalization like...
2013 / D.T. Matt, E. Rauch -
On the Possibility to Run an Internal Combustion Engine on Acetylene and Alcohol
Abstract It is well known that acetylene is a high flammable and explosive compound. In comparison with commercial liquid fuels, very wide flammability limits and a low Octane Number have relegated the acetylene into the “iperdetonat” fuels...
2014 / S. Brusca, R. Lanzafame, A. Marino Cugno Garrano, M. Messina -
MHD squeezing flow between two infinite plates
Abstract Magneto hydrodynamic (MHD) squeezing flow of a viscous fluid has been discussed. Conservation laws combined with similarity transformations have been used to formulate the flow mathematically that leads to a highly nonlinear ordinary...
2013 / Umar Khan, Naveed Ahmed, Z.A. Zaidi, Mir Asadullah, Syed Tauseef Mohyud-Din -
Evaluation of Piecewise Polynomial Equations for Two Types of Thermocouples2013 / Andrew Chen, Chiachung Chen
-
Slotted Blades Savonius Wind Turbine Analysis by CFD2013 / Andrea Alaimo, Antonio Esposito, Alberto Milazzo, Calogero Orlando, Flavio Trentacosti
-
Modeling the Formation of Transverse Weld during Billet-on-Billet Extrusion2014 / Yahya Mahmoodkhani, Mary Wells, Nick Parson, Chris Jowett, Warren Poole
-
Comparative Study on Different Energy Management Strategies for Plug-In Hybrid Electric Vehicles2013 / Ximing Wang, Hongwen He, Fengchun Sun, Xiaokun Sun, Henglu Tang
-
Tool wear predictability estimation in milling based on multi-sensorial data2015 / P. Stavropoulos, A. Papacharalampopoulos, E. Vasiliadis, G. Chryssolouris