Mechanical engineering topic list of research papers
-
Remaining useful life prognostics for aeroengine based on superstatistics and information fusion
Abstract Remaining useful life (RUL) prognostics is a fundamental premise to perform condition-based maintenance (CBM) for a system subject to performance degradation. Over the past decades, research has been conducted in RUL prognostics for...
2014 / Junqiang Liu, Malan Zhang, Hongfu Zuo, Jiwei Xie -
Performance Analysis on Carrier Phase-Based Tightly-Coupled GPS/BDS/INS Integration in GNSS Degraded and Denied Environments2015 / Houzeng Han, Jian Wang, Jinling Wang, Xinglong Tan
-
Flow past a square-section cylinder with a wavy stagnation face2002 / RUPAD M. DAREKAR, SPENCER J. SHERWIN
-
Comparative study of conjugate gradient algorithms performance on the example of steady-state axisymmetric heat transfer problem2013 / Paweł Ocłoń, Stanisław Łopata, Marzena Nowak
-
Analytical model of high-voltage transmission line subjected to thedownburst wind with rainfall2015 / C. Zhou, Y. Liu
-
A Six Sigma Approach for Precision Machining in Milling
Abstract Controlling the process variations on the perimeter of a component to the targeted mean in milling is a huge challenge. Several factors such as spindle speed, feed rate, depth of cut, etc. affects this process variation. In this paper,...
2014 / Ganesh Kumar Nithyanandam, Radhakrishnan Pezhinkattil -
Investigation of the Soot Formation in Ethylene Laminar Diffusion Flames When Diluted with Helium or Supplemented by Hydrogen2014 / Huayong Zhao, Richard Stone, Ben Williams
-
Drying of Pigment-Cellulose Nanofibril Substrates2014 / Oleg Timofeev, Katariina Torvinen, Jenni Sievänen, Timo Kaljunen, Jarmo Kouko, et al.
-
Simultaneous Identification of Moving Vehicles and Bridge Damages Considering Road Rough Surface2013 / Qingxia Zhang, Łukasz Jankowski, Zhongdong Duan
-
An Analytical Model for Predicting the Stress Distributions within Single-Lap Adhesively Bonded Beams2014 / Xiaocong He, Yuqi Wang
-
Electrical Discharge Machining of Al (6351)-5% SiC-10% B 4 C Hybrid Composite: A Grey Relational Approach2014 / S. Suresh Kumar, M. Uthayakumar, S. Thirumalai Kumaran, P. Parameswaran, E. Mohandas
-
A New Mathematical Model for Flank Wear Prediction Using Functional Data Analysis Methodology2014 / Sonja Jozić, Branimir Lela, Dražen Bajić
-
Lightweight Design of an Outer Tie Rod for an Electrical Vehicle2014 / Young-Chul Park, Seung-Kul Baek, Bu-Kyo Seo, Jong-Kyu Kim, Kwon-Hee Lee
-
Cooperative Control Method of Active and Semiactive Control: New Framework for Vibration Control2014 / Kazuhiko Hiramoto
-
Numerical Study on Transient Heat Transfer of a Quartz Lamp Heating System2014 / Yan Yu, Pingjian Ming, Song Zhou
-
A Two-Stage Fuzzy Logic Control Method of Traffic Signal Based on Traffic Urgency Degree2014 / Yan Ge
-
Overhead Transmission Lines Deicing under Different Incentive Displacement2014 / Qing He, Xi-feng Lv, Xiao-tong Zhao
-
Effect of parameters on local stress field in single-lap bolted joints with the interference fit2016 / J. Jiang, Y. Bi
-
Separated representations of 3D elastic solutions in shell geometries2014 / Brice Bognet, Adrien Leygue, Francisco Chinesta
-
Representing and constructing liquefaction cycle alternatives for FLNG FEED using system entity structure concepts2015 / Sol Ha, Kyu-Yeul Lee