Mechanical engineering topic list of research papers
-
Examining Factors of Walking Disutility for Microscopic Pedestrian Model – A Virtual Reality Approach
Abstract Understanding mechanisms of microscopic pedestrian behaviour is important for pedestrian simulation, which is a useful tool for the design of pedestrian infrastructure. Interest in understanding pedestrian walking behaviour is also...
2013 / Takamasa Iryo, Miho Asano, Shinta Odani, Shogo Izumi -
Heat Dissipation using Minimum Counter Flow Jet Ejection During Spacecraft Re-Entry
Abstract A major problem of spacecraft re-entry is the extreme heat generated. Sink and ablation cooling are commonly used but the cost of building and implementing such heat protection systems is very high. The issue of heat dissipation has,...
2012 / Y. Zheng, N.A. Ahmed, W. Zhang -
Analysis of R134a–DMAC vapour absorption refrigeration system with add-on components
Abstract R134a–DMAC vapour absorption refrigeration system (VARS) needs rectifier. Because of incomplete rectification, a small amount of DMAC is carried to evaporator. It results in a temperature gradient and also formation of residual liquid in...
2012 / Subhadip Roy, M.P. Maiya -
Theoretical modelling of hot gas ingestion through turbine rim seals
Abstract The rim seals of gas turbines are used to prevent or reduce the ingestion of hot mainstream gas into the wheel-space between the turbine rotor and its adjacent stationary casing. The ingestion is caused by local pressure differences between ...
2012 / J. Michael Owen -
Development of a Pneumatically-Driven Robotic Forceps with a Flexible Wrist Joint
Abstract The present paper describes a pneumatically-driven forceps manipulator for minimally-invasive robot surgery that has a simplified flexible wrist joint for easy fabrication, cost reduction and future miniaturization. The joint structure...
2013 / Daisuke Haraguchi, Kotaro Tadano, Kenji Kawashima -
Wire Electrical Discharge Milling using a Wire Guide with Reciprocating Rotation
Abstract EDM is a useful method for machining hard materials. Particularly, ED-milling using a simple bar or pipe electrode is an attractive method to machine 3D cavities. However, it is difficult to suppress the electrode wear completely. On the...
2013 / H. Gotoh, T. Tani, M. Okada, A. Goto, T. Masuzawa, et al. -
The Multiscale Stochastic Model of Fractional Hereditary Materials (FHM)
Abstract In a recent paper the authors proposed a mechanical model corresponding, exactly, to fractional hereditary materials (FHM). Fractional derivation index 13 E [0,1/2] corresponds to a mechanical model composed by a column of massless...
2013 / Mario Di Paola, Massimiliano Zingales -
Optimized post combustion carbon capturing on coal fired power plants
Abstract Worldwide coal contributes to over 40% of the electricity generation today and its share is expected to increase steadily over the coming decades. The continued dominance of coal in global energy structure and the growing concern of climate ...
2011 / Brian Stöver, Christian Bergins, Jürgen Klebes -
Design of thermostatic tank and control system
Abstract Based on the isothermal forming technique of pressing and spinning, designed the precision formational equipment. Furthermore, auxiliary equipped the thermostatic oil tank through the heat conduction computation, the heat conductivity...
2010 / Chunsheng Ma, Zhimin Zhang -
Research on Bell-Shaped Vibratory Angular Rate Gyro’s Character of Resonator2013 / Zhong Su, Mengyin Fu, Qing Li, Ning Liu, Hong Liu
-
Remote Sensor for Spatial Measurements by Using Optical Scanning2009 / Oleg Sergiyenko, Wilmar Hernandez, Vira Tyrsa, Luis Felipe Devia Cruz, Oleg Starostenko, et al.
-
Experimental Investigation of a Forward Swept Rotor in a Multistage Fan with Inlet Distortion2011 / Aspi R. Wadia
-
The Analytical Expression for the Mass Flux in the Wet/Dry Areas Method2012 / Xianyun Wen
-
General Computational Model for Human Musculoskeletal System of Spine2012 / Kyungsoo Kim, Yoon Hyuk Kim, SuKyoung Lee
-
Axial-Symmetry Numerical Approaches for Noise Predicting and Attenuating of Rifle Shooting with Suppressors2011 / Shi-Wei Lo, Chang-Hsien Tai, Jyh-Tong Teng
-
Study of Tool Wear and Overcut in EDM Process with Rotary Tool and Magnetic Field2012 / Reza Teimouri, Hamid Baseri
-
Modeling and Fuzzy PDC Control and Its Application to an Oscillatory TLP Structure2010 / Cheng-Wu Chen
-
Numerical Modelling of Squeeze Film Performance between Rotating Transversely Rough Curved Circular Plates under the Presence of a Magnetic Fluid Lubricant2012 / Nikhilkumar D. Abhangi, G. M. Deheri
-
Robust Optimal Design of Fiber-Reinforced Composite Cylinder with Metallic Liner2012 / Chwei-Yuh Chiou
-
Exergoeconomic Evaluation of a Modern Ultra-Supercritical Power Plant2012 / Ligang Wang, Yongping Yang, Changqing Dong, Zhiping Yang, Gang Xu, et al.