Mechanical engineering topic list of research papers
-
Experimental Testing and Full and Homogenized Numerical Models of the Low Velocity and Dynamic Deformation of the Trapezoidal Aluminium Corrugated Core Sandwich2014 / C. Kιlιçaslan, İ. K. Odacι, A. Taşdemirci, M. Güden
-
Elasto-multi-body dynamics of a multicylinder internal combustion engine2003 / M Kushwaha, S Gupta, P Kelly, H Rahnejat
-
A Feature Extraction Method Based on Information Theory for Fault Diagnosis of Reciprocating Machinery2009 / Huaqing Wang, Peng Chen
-
Approximate Analytical Solution for One-Dimensional Solidification Problem of a Finite Superheating Phase Change Material Including the Effects of Wall and Thermal Contact Resistances2012 / Hamid El Qarnia, Fayssal El Adnani, El Khadir Lakhal
-
A Wide Linear Range Eddy Current Displacement Sensor Equipped with Dual-Coil Probe Applied in the Magnetic Suspension Flywheel2012 / Jiancheng Fang, Tong Wen
-
Study on the Performance of the Solar Cooling System Using Cavity Receiver Based on the Neural Network
Abstract A solar absorption cooling system with cavity receiverfor demonstration was introduced. The system consisted of a double-effectlithium bromide chiller and a parabolic trough concentrator with cavitysolar receiver.The high temperature heat...
2015 / Haoju Li, Shuhuai Wang, Zheng Zhang, Xu Xu, Kai Song -
A simulation study on the multi-pass rolling bond of 316L/Q345R stainless clad plate2015 / Q. Qin, D.-t. Zhang, Y. Zang, B. Guan
-
An Intelligent Traffic Flow Control System Based on Radio Frequency Identification and Wireless Sensor Networks2014 / Kuei-Hsiang Chao, Pi-Yun Chen
-
Investigation of Cutting Forces, Surface Roughness and Tool Wear during Laser Assisted Machining of SKD11Tool Steel
Abstract The present work deals with the machining of Tool steel - SKD 11 which is widely used in industries for making dies and molds. It is chosen for its toughness, strength, and hardness maintained up to high temperature. However, the properties ...
2014 / S. Xavierarockiaraj, P. Kuppan -
Thermodynamic analysis of PID temperature controlled heat pump system
Abstract In the current research, a heat pump fluidized bed dryer a with PID temperature control was designed. Drying air temperature was determined as 40°C and it was controlled through this system with ±0.36°C uncertainty. The designed and...
2013 / Ali Etem Gürel, İlhan Ceylan -
Wake Topology of Curved Cylinders at Low Reynolds Numbers2004 / A. Miliou, S.J. Sherwin, J.M.R. Graham
-
Study on Hydrodynamic Pressure in Grinding Contact Zone Considering Grinding Parameters and Grinding Wheel Specifications
Abstract In the grinding process, coolant lubricant is used to lubricate and mainly to transmit the heat generated in the contact zone. Grinding wheel accelerates a portion of the coolant lubricant into the contact zone. As e resault of the wedge...
2014 / Alireza Vesali, Taghi Tawakoli -
Safety Discussion and Precaution Measures about Laser Beam Welding of Pyrotechnic Actuator
Abstract Structure of pyrotechnic actuator used in AP1000 nuclear power plant squib valve was introduced, and laser beam welding danger of pyrotechnic actuator was analyzed. Sulfur-Free Black Powder charged in pyrotechnic actuator was test by...
2012 / Yingchun Zhang, Wei Zhang, Anmin Yang, Shubin Yang, Fuping Gao -
Research of Step-down Stress Accelerated Degradation Data Assessment Method of a Certain Type of Missile Tank
Abstract The performance degradation rates of the missile tank are generally time-varying functions uneasily evaluated by general classical evaluation methods. This paper develops a segmented nonlinear accelerated degradation model (SNADM) based on...
2012 / Jun YAO, Mingge XU, Weiqiang ZHONG -
Potential improvement of aerodynamic performance by morphing the nacelle inlet
Abstract In this work numerical investigations of the aerodynamic performance of an adaptive turbofan-engine inlet are performed. The adaptation is made on the inner front part of the symmetric inlet by changing the positions of two contour knots,...
2016 / Frane Majić, Gunilla Efraimsson, Ciarán J. O'Reilly -
Modeling and Analysis of Helicopter Thermal and Infrared Radiation
Abstract The temperature distributions on the helicopter airframe and in the exhaust plume are affected seriously by the engine exhaust system, rotor downwash and solar irradiance. To precisely simulate temperature distribution on the helicopter...
2011 / Chengxiong PAN, Jingzhou ZHANG, Yong SHAN -
Motion State Analysis and Seal Ability Study on the Magnetic Fluid Seal of Reciprocating Shaft
Abstract The authors have studied the motion mechanism of the magnetic fluid in a reciprocating seal gap, on the basis of which the authors obtain an anti-pressure formula of the reciprocating shaft magnetic fluid seal from general Navier-Stokes...
2011 / De-cai LI, Jian-ping HONG, Qing-xin YANG, Xiu-ting WANG -
Prediction Model of Transport Sharing Rates of the Comprehensive Transportation Corridor
Abstract Aiming at the problem that the prediction of transport structure doesn’t have enough accuracy, in this paper the influence factors of transport structure were determined, and the transport structure of the future characteristics year was...
2013 / Chen Hong, Zhang Bin, You Yue-sheng, Xie Xiang-chun -
How to Design a Logo
Abstract This paper talks about the implementation of a lot of graphic elements to design such a special structure known as logo. To design a logo is important to have very good knowledge in graphics, the management of colours, geometric shapes,...
2014 / Victor Adîr, George Adîr, Nicoleta Elisabeta Pascu -
An iterative boundary element method for a wing-in-ground effect2015 / Omer Kemal Kinaci