Mechanical engineering topic list of research papers
-
A Finite Points Method Approach for Strain Localization Using the Gradient Plasticity Formulation2014 / Luis Pérez Pozo, Andy Campos, Sheila Lascano, Sergio Oller, Antonio Rodríguez-Ferran
-
Some Movement Mechanisms and Characteristics in Pebble Bed Reactor2014 / Xingtuan Yang, Yu Li, Nan Gui, Xinlong Jia, Jiyuan Tu, et al.
-
Statistical Analysis of Traffic Accidents in Shanghai River Crossing Tunnels and Safety Countermeasures2014 / Linjun Lu, Jian Lu, Yingying Xing, Chen Wang, Fuquan Pan
-
Model and Method for Multiobjective Time-Dependent Hazardous Material Transportation2014 / Zhen Zhou, Ada Che, Feng Chu, Chengbin Chu
-
Analyses of Effects of Cutting Parameters on Cutting Edge Temperature Using Inverse Heat Conduction Technique2014 / Marcelo Ribeiro dos Santos, Sandro Metrevelle Marcondes de Lima e Silva, Álisson Rocha Machado, Márcio Bacci da Silva, Gilmar Guimarães, et al.
-
Experimental Characterization of Orientation Formation in a Mold Cavity with Sudden Contraction2014 / K. A. Olivero, M. C. Altan
-
Dynamical equations of multibody systems on Lie groups2015 / W. Yu, Z. Pan
-
Some formulas of variance of uncertain random variable2014 / Yuhong Sheng, Kai Yao
-
Study on the creep behavior of bonded metallic joints2014 / Rodrigo A Queiroz, Eduardo M Sampaio, Vitor J Cortines, Ney RF Rohem
-
The top heat mode of closed loop oscillating heat pipe with check valves at the top heat mode (THMCLOHP/CV): a thermodynamic study2014 / Nipon Bhuwakietkumjohn, Thanya Parametthanuwat
-
Design and Application of Virtual Reality System in Fully Mechanized Mining Face
Abstract This paper introduced function design and development flow of virtual reality system of fully mechanized mining face. In the process of geometric modeling, element partitioning, instance,atomization and other technologies were used to...
2012 / Zhang Xiaoqiang, Wang An, Li Jianzhong -
Mechanistic identification of cutting force coefficients in bull-nose milling process
Abstract An improved method to determine cutting force coefficients for bull-nose cutters is proposed based on the semi-mechanistic cutting force model. Due to variations of cutting speed along the tool axis in bull-nose milling, they affect...
2013 / Ge Gao, Baohai Wu, Dinghua Zhang, Ming Luo -
Parameter optimization of controllable local degree of freedom for reducing vibration of flexible manipulator
Abstract Parameter optimization of the controllable local degree of freedom is studied for reducing vibration of the flexible manipulator at the lowest possible cost. The controllable local degrees of freedom are suggested and introduced to the...
2013 / Yushu Bian, Zhihui Gao -
A Combination of Silicon Micro-gyroscope that Application Rotary Missile Attitude Control System
Abstract For the technical requirements of rotary missile attitude control, there developed a new type of combination of silicon micro-gyroscope, it mainly consists of two perpendicular installation of micro-mechanical pendulum and the circuit. This ...
2011 / Sheng-jie Qin, Fu-xue Zhang -
Improving the Navigability of a Hexapod Robot using a Fault-Tolerant Adaptive Gait2012 / Umar Asif
-
Feasibility of Solar Powered Cooling Device for Electric Car
Abstract This work studies the feasibility of improving the thermal comfort in an electric UXV car cabin through a cooling device. The main components of the device consist of a membrane solar panel, four axial fans, and a rechargeable battery pack. ...
2012 / Y.-A. Yan, C.-Y. Tseng, J.C. Leong -
MIMO System Reduction Using Modified Pole Clustering and Genetic Algorithm2009 / C. B. Vishwakarma, R. Prasad
-
A New Measurement Model for Main Steam Flow of Power Plants
Abstract Accuracy of existing measurement models for main steam flow in power plants is always unsatisfied. In this paper, a model with higher accuracy for main steam flow measurement was proposed. Accurate values of main steam flow can be obtained...
2012 / Jizhen Liu, Shu Yan, Deliang Zeng -
Investigation of Finite Amplitude Stability Due to Process Damping in Milling
Abstract Finite amplitude stability due to process damping is an intermediate state between fully stable and fully unstable vibrations in machining. In this state, the amplitude of vibration increases and stabilizes at a certain magnitude before the ...
2012 / K. Ahmadi, F. Ismail -
Mathematic simulation of +13 mm particles motion in jig
Abstract To meet the needs of the jigging process control, attempt to combine the studying on jigging mechanism with the operating and detecting parameters so as to use them in practical producing control. On the basis of studying the motion...
2009 / Kuang Ya-li, Zhang Jun, Zhang Hai-yang, Ge Jun