Mechanical engineering topic list of research papers
-
Numerical Investigation of Wave Slamming of Flat Bottom Body during Water Entry Process2014 / Xiaozhou Hu, Shaojun Liu
-
The Research on Low Carbon Logistics Routing Optimization Based on DNA-Ant Colony Algorithm2014 / Liyi Zhang, Ying Wang, Teng Fei, Hongwei Ren
-
Investigation of wear and tool life of coated carbide and cubic boron nitride cutting tools in high speed milling2015 / P. Twardowski, S. Legutko, G. M. Krolczyk, S. Hloch
-
Experimental and numerical investigation of fully developed forced convection of water-based Fe3O4 nanofluid passing through a tube in the presence of an alternating magnetic field2015 / M. H. Dibaei Bonab, M. B. Shafii, M. H. Nobakhti
-
Efficiency analysis of the dynamic traffic control for an urban highway2015 / Ali Kesten, Murat Ergün
-
Thermal response test for shallow geothermal applications: a probabilistic analysis approach2015 / Francesco Tinti, Roberto Bruno, Sara Focaccia
-
Development of 3D viewer based teleoperation interface for Human Support Robot HSR2014 / Hiroaki Yaguchi, Kenji Sato, Mitsuharu Kojima, Kiyohiro Sogen, Yutaka Takaoka, et al.
-
The robot that can achieve card magic2015 / Ryoma Koretake, Makoto Kaneko, Mitsuru Higashimori
-
Towards uncertain network optimization2015 / Jin Peng, Bo Zhang, Shengguo Li
-
Effect of Acoustic Excitation on Flow Asymmetry over Slender Body at High Angles of Attack
Abstract A new kind of flow control method, acoustic excitation, was applied to control flow asymmetry over a slender body at high angles of attack. Results show that acoustic excitation could improve the asymmetric behaviors as long as controlling...
2012 / Yuanjing Wang, Zhong He, Dawei Liu -
Entropy Generation Analysis of Desalination Technologies2011 / Karan H. Mistry, Ronan K. McGovern, Gregory P. Thiel, Edward K. Summers, Syed M. Zubair, et al.
-
An Equivalent Tolerance Design Method for Imaging System
Abstract The traditional tolerance analysis of optical design does not consider the capability of the manufacturing process and the quality variation of the assembly process caused by the manufacturing errors of optical and mechanical components....
2011 / Chun-Li Chang, Min-Wei Hung, Kuo-Cheng Huang -
CAD and CAE Analysis for Siphon Jet Toilet
Abstract The high precision 3D laser scanner with the dual CCD technology was used to measure the original design sample of a siphon jet toilet. The digital toilet model was constructed from the cloud data measured with the curve and surface fitting ...
2011 / Yuhua Wang, Guoji Xiu, Haishu Tan -
Research on Control Strategy of Two Independent Rear Wheels Drive Electric Vehicle
Abstract The 4 DOFS dynamic simulation model of two independent rear wheels drive electric vehicle was built by the Matlab/Simulink software. Asynchronous motors were used in the drive wheels .The motor vector control algorithm and the slip ratio...
2012 / Gang Li, Wei Hong, Daming Zhang, Changfu Zong -
The application of formal perception of gestalt in architectural education
Abstract It's well known that, architectural design is a problem solving process which has the purpose of reaching a synthesis through analytic approaches, involving activities which try to find out appropriate combinations of physical (location,...
2011 / S. Sema Uzunoglu, Kozan Uzunoglu -
The Fault Diagnosis of Blower Ventilator Based-on Multi-class Support Vector Machines
Abstract Blower ventilators are one of the main rotating equipment in the thermal power plant, supervising and forecasting the faults of the operating ventilator can significantly improve the safety and economy of ventilator as well as guarantee the ...
2012 / Xing-wei Wu -
Entropy Generation Due to Laminar Incompressible Forced Convection Flow Through Parallel-Plates Microchannel2008 / Osamah Haddad, Mohammad Abuzaid, Mohammad Al-Nimr
-
Device development and experimental study on the methane explosion ignited by sparks of cable bolt slippage (breakage)
Abstract The first experimental device in the world was designed for studying methane explosion ignited by sparks of cable bolt slippage (breakage), which was designed with the same size as underground and the length of cable bolt can be tested as...
2009 / Xu Jia-lin, Wu Ren-lun, Xu Guang, Qin Wei -
Review of Vibration Signals Trend Forecasting Methods
Abstract Vibration signals are important information for system failures. Forecasting the trend of vibration signals is an important content of condition monitoring, life estimation and fault diagnosis. The advantages, disadvantages and applicable...
2011 / Hao Li, Cheng Wang, Cancan Chen, Guirong Yan -
Experimental Analysis and Geometrical Modeling of Cutting Conditions Effect in 5 Axis Milling with Ti6Al4 V Alloy
Abstract The 5 axis continuous milling is an advanced technique for free-form surfaces manufacturing. In finishing, this technique uses ball-end or hemispherical milling cutter. This type of operation for 5 axis milling allows the possibility to...
2012 / David Prat, Guillaume Fromentin, Gérard Poulachon, Emmanuel Duc