Mechanical engineering topic list of research papers
-
Study on the Mechanism of the Position Adjustable Rotors for Sediment Deposition Reduction
Abstract For to reduce and protect the sediment deposition at downstream river course under the tide gates, the position adjustable rotors for sediment deposition reduction is designed. This paper through the physical experiment study on the flow...
2011 / Jibao Wang -
Design of a series visco-elastic actuator for multi-purpose rehabilitation haptic device2011 / Jakob Oblak, Zlatko Matjačić
-
A Multi-Fault Diagnosis Method for Sensor Systems Based on Principle Component Analysis2009 / Daqi Zhu, Jie Bai, Simon X. Yang
-
Second Law Analysis of Viscoelastic Fluid over a Stretching Sheet Subject to a Transverse Magnetic Field with Heat and Mass Transfer2010 / Soraya Aïboud, Salah Saouli
-
Analysis of Thermal Field on Integrated LED Light Source Based on COMSOL Multi-physics Finite Element Simulation
Abstract This paper obtained the average integrated heat transfer coefficient for the thermal resistance of a classic of integrated LED light source and its cooling fin-root on the basis of thermal circuit method. Simulation analysis on its...
2011 / Jingsong Li, Qingxin Yang, Pingjuan Niu, Liang Jin, Bo Meng, et al. -
Delay Independent Criterion for Multiple Time-delay Systems
Abstract Based on the fuzzy Lyapunov method, this work addresses the stability conditions for nonlinear systems with multiple time delays to ensure the stability of building structure control systems. The delay independent conditions are derived via ...
2012 / C.J. Chang, K.F.R. Liu, K. Yeh, C.W. Chen, P.Y. Chung -
A new fuzzy parameters reliability analysis model
Abstract The most difficult form of its periodicity is one of the conditions of the elements which traversing the entire results of the corresponding operations, when the fuzzy numbers in the use of traditional methods of operation principle of...
2012 / Haijun Chen, Xijuan Lou -
On the consistent formulation of torques in a rotationless framework for multibody dynamics
Abstract A rotationless formulation of flexible multibody dynamics in terms of natural coordinates is considered. Since natural coordinates do not comprise rotational parameters, the consistent formulation and numerical discretization of actuating...
2012 / P. Betsch, N. Sänger -
Heat Loss Comparison Between Hydrogen, Methane, Gasoline and Methanol in a Spark-Ignition Internal Combustion Engine
Abstract Understanding the heat transfer mechanism from the combustion gases to the walls inside an internal combustion engine is key in the search for higher efficiencies, higher power outputs and lower emissions. Current heat transfer modeling...
2012 / Joachim Demuynck, Michel De Paepe, Ivan Verhaert, Sebastian Verhelst -
Design of Automatic Control System for NDT Device
Abstract The article designed a kind of new nondestructive testing device control system to increase the test efficiency and improve the reliability of computed tomography. This system could not only precisely locate and control the turntable and...
2012 / Liu Bin, Zhou Min -
Free Vibrations of Unsymmetrically Laminated Anisotropic Plates with Clamped Edges2007 / C. W. Bert, B. L. Mayberry
-
Reprint of:Future Challenges in Computational Aeroacoustics for Fan Broadband and Combustor Noise
Abstract Two critical areas for the design of quiet gas turbine engines, fan broadband and combustor noise, are briefly reviewed. Both of these noise sources are sensitive to local aerodynamic and geometric variations and thus are ideally suited for ...
2010 / Oliver Atassi, Jonathan J. Gilson -
Towards Fast Tracking of the Keyhole Geometry
Abstract We describe a sensor principle permitting the fast online measurement of the position of the optical process emissions in deep penetration laser welding. Experiments show a strong correlation between the position of the vapour plume and the ...
2011 / C. Brock, R. Hohenstein, M. Schmidt -
Abrasive Waterjet Turning of High Performance Materials
Abstract The cutting of high performance materials requires specific machine tools and cutting tools. The wear resistance of cutting tools is important for turning of hypereutectic aluminium silicon or titanium aluminide alloys. Abrasive waterjet...
2012 / Eckart Uhlmann, Karsten Flögel, Michael Kretzschmar, Fabian Faltin -
The Exergy Analysis Of Gas Cooler In CO2 Heat Pump System
Abstract The (H)CFC-phase-out and the fear for future problems for other synthetic working fluids, because of their known and unknown impact on the environment, have introduced a rising interest in environmentally safe natural working fluids. CO2 is ...
2012 / Yingbai Xie, Zhichao Wang, Kuikui Cui, Xuedong Zhang -
Test method for the propensity of coal to spontaneous combustion
Abstract The propensity of coal to spontaneous combustion demonstrates the inherent character of the oxidation capacity at normal temperature. Currently, based on simulating spontaneous combustion of coal using adiabatic oxidation and...
2009 / De-ming Wang, Qi Xu-yao, Zhong Xiao-xing, Gu Jun-jie -
Modeling of internal combustion engine emissions by LOLIMOT algorithm
Abstract In this work, a neural network model of internal combustion engine is presented. First, we collect data of a 1.6L gasoline engine which was used for deriving an engine neural model. The engine was coupled to a hydraulic dynamometer to...
2012 / J.D. Martínez-Morales, Elvia Palacios, G.A. Veláazquez Carrillo -
An attempt of a new motion measurement method for alpine ski turns using inertial sensors
Abstract This paper proposes the motion measurement method of skiing turn using inertial sensor. This method calculates the joint angle of the skier gliding on the actual snow field using the information from the inertial sensor units. The sensor...
2012 / Akiko Kondo, Hitoshi Doki, Kiyoshi Hirose -
Switching Between Formation in a Moving Shape for Multi-Robots via Synchronization Approach
Abstract This paper extends the synchronization approach for formation control of multiple mobile robots. In this work, the formation shape is moving in a straight line while it is changing with time. Each robot is controlled to track its desired...
2012 / Ibrahim M.H. Sanhoury, Shamsudin H.M. Amin, Abdul Rashid Husain -
Practical solution for improving the mechanical behaviour of the composite materials reinforced with flax woven fabric2015 / C. Cerbu