Mechanical engineering topic list of research papers
-
Modal Analysis of Worm and Worm Gear Based on ANSYS Workbench2015 / Yichang Liu, Chunlin Tian, Tao Liu, Fanwu Kong
-
Optimization of the machining parameters for EDM wire cutting of Tungsten Carbide2016 / Gaurav Kumar, J S Tiwana, Ashish Singla
-
Optimization of resistance welding by using electric servo actuator2017 / Zygmunt Mikno, Mariusz Stepien, Boguslaw Grzesik
-
The Measurement of Wall Shear Stress in the Low-Viscosity Liquids2013 / M. Schmirler, J. Matěcha, H. Netřebská, J. Ježek, J. Adamec
-
Damping Performance of Taut Cables with Passive Absorbers Incorporating Inerters2016 / Jiannan Luo, Jason Zheng Jiang, John H G Macdonald
-
Cutting force and machine kinematics constrained cutter location planning for five-axis flank milling of ruled surfaces
Abstract Five-axis flank milling has been commonly used in the manufacturing of complex workpieces because of its greater productivity than that of three-axis or five-axis end milling. The advantage of this milling operation largely depends on...
2017 / Ke Xu, Jiarui Wang, Chih-Hsing Chu, Kai Tang -
Real-time altitude control for a quadrotor helicopter using a super-twisting controller based on high-order sliding mode observer2017 / Ivan Gonzalez-Hernandez, Filiberto Munoz Palacios, Sergio Salazar Cruz, Eduardo Steed Espinoza Quesada, Rogelio Lozano Leal
-
Heat and Mass Transfer of the Droplet Vacuum Freezing Process Based on the Diffusion-controlled Evaporation and Phase Transition Mechanism2016 / Zhijun Zhang, Jingxin Gao, Shiwei Zhang
-
A study of rotor and platform design trade-offs for large-scale floating vertical axis wind turbines2016 / D. Todd Griffith, Joshua Paquette, Matthew Barone, Andrew J. Goupee, Matthew J. Fowler, et al.
-
Sensorless interior permanent magnet synchronous motor control with rotational inertia adjustment2017 / Yongle Mao, Jiaqiang Yang, Dejun Yin, Yangsheng Chen
-
The study on minimum uncut chip thickness and cutting forces during laser-assisted turning of WC/NiCr clad layers2017 / D. Przestacki, T. Chwalczuk, S. Wojciechowski
-
A single-phase axially-magnetized permanent-magnet oscillating machine for miniature aerospace power sources2017 / Yi Sui, Ping Zheng, Luming Cheng, Weinan Wang, Jiaqi Liu
-
Tag location method integrating GNSS and RFID technology2016 / Meng Du, Changfeng Jing, Mingyi Du
-
Experimental investigation of CNG and gasoline fuels combination on a 1.7 L bi-fuel turbocharged engine2016 / Abbas Raei Tabar, Ali Asghar Hamidi, Hossein Ghadamian
-
Dance motion capture and composition using multiple RGB and depth sensors2017 / Yejin Kim
-
Tracking error constrained robust adaptive neural prescribed performance control for flexible hypersonic flight vehicle2017 / Zhonghua Wu, Jingchao Lu, Jingping Shi, Qing Zhou, Xiaobo Qu
-
Single-input adaptive fuzzy sliding mode control of the lower extremity exoskeleton based on human–robot interaction2017 / Xinglai Jin, Shiqiang Zhu, Xiaocong Zhu, Qingcheng Chen, Xuequn Zhang
-
Synthesised H ∞ / μ Control Design for Dynamically Substructured Systems2016 / T Yamaguchi, D P Stoten
-
Gain Scheduling of PID Controller Based on Fuzzy Systems2016 / Sandeep Singh, Mandeep Kaur
-
Multidimensional prognostics for rotating machinery: A review2017 / Xiaochuan Li, Fang Duan, David Mba, Ian Bennett