Mechanical engineering topic list of research papers
-
The attitude adjustment algorithm in drilling end-effector for aviation2016 / P. Yuan, T. Lai, Y. Li, W. Han, M. Lin, et al.
-
Study of Aerodynamic Configuration Design and Wind Tunnel Test for Solar Powered Buoyancy-lifting Vehicle in the Near-space
Abstract Aconfiguration of buoyancy-lifting vehicleflying in near-space by combinationthe configuration characteristics of high-altitude airships and solar UAV aerodynamic were proposed .Through the numerical simulation method, the aerodynamic...
2015 / Guangqiang Chen, Bingyan Chen, Pengfei Li, Peng Bai, Chunqun Ji -
Study of a MEMS Vibratory Gyroscope Using Adaptive Iterative Learning Control2014 / Xiaochun Lu, Juntao Fei
-
Finite time motion control for a launching platform based on sliding mode disturbance observer2016 / Y. Qiu, J. Hu, H. Lu, L. Liu
-
MR- and ER-Based Semiactive Engine Mounts: A Review2013 / Mohammad Elahinia, Constantin Ciocanel, The M. Nguyen, Shuo Wang
-
Variational surface design under normal field guidance
Abstract This paper proposes a novel method for shape design of a Bézier surface with given boundary curves. The surface is defined as the minimizer of an extended membrane functional or an extended thin plate functional under the guidance of a...
2015 / Weidong Wu, Xunnian Yang -
Practical Damping Identification of FAST Cable Suspension2014 / J. Sun, H. Li, W. Zhu
-
Research of Impact Load in Large Electrohydraulic Load Simulator2014 / Yongguang Liu, Xiaohui Gao, Zhongcai Pei
-
A Novel Angle Computation and Calibration Algorithm of Bio-Inspired Sky-Light Polarization Navigation Sensor2014 / Zhiwen Xian, Xiaoping Hu, Junxiang Lian, Lilian Zhang, Juliang Cao, et al.
-
Charging valve of the full hydraulic braking system2016 / J. Chen, X. Liu, T. Wang, X. Gong, H. Sun, et al.
-
Fuzzy Linguistic Optimization on Surface Roughness for CNC Turning2010 / Tian-Syung Lan
-
Non-contact test set-up for aeroelasticity in a rotating turbomachine combining a novel acoustic excitation system with tip-timing2014 / O Freund, M Montgomery, M Mittelbach, J R Seume
-
ROAD ACCIDENTS PROFILE IN TAIWAN2014 / Cheng-Min FENG
-
Investigation of hydraulic force of a 1000-MW pressurized water reactor under hypothetical drop accident of core barrel assembly2016 / J. Jiang, L. Zhang, Y. Li, Y. Fu
-
A new model for the optimization of periodic inspection intervals with failure interaction: A case study for a turbine rotor
Abstract Inspection is one of the important activities to detect and fix failures in repairable system. Optimization of inspection intervals has critical role in maintenance cost and operating system. When a component fails, it is renewed or...
2015 / Esmaeil Rezaei -
Flapwise bending vibration analysis of functionally graded rotating double-tapered beams2015 / N. V. Ramesh Maganti, Mohan Rao Nalluri
-
An experimental investigation of shell and tube latent heat storage for solar dryer using paraffin wax as heat storage material
Abstract In the presented study the shell and tube type latent heat storage (LHS) has been designed for solar dryer and paraffin wax is used as heat storage material. In the first part of the study, the thermal and heat transfer characteristics of...
2015 / Ashish Agarwal, R.M. Sarviya -
Research on Developing DPF Blowback Heating Regeneration Device
Abstract Development of human society faces two important subjects-energy crisis and environmental pollution. In this paper, Carbon smoke particulate materials (PM)-one of the main pollutants discharged by diesel were studied, and the...
2011 / Minggang Zheng, Hui Gao, Xiaohui Zhu -
Reconfiguration analysis of a 3-DOF parallel mechanism using Euler parameter quaternions and algebraic geometry method
Abstract This paper deals with the reconfiguration analysis of a 3-DOF (degrees-of-freedom) parallel mechanism (PM) with multiple operation modes – a disassembly-free reconfigurable PM – using the Euler parameter quaternions and algebraic geometry...
2014 / Xianwen Kong -
Static Analysis of Functionally Graded Piezoelectric Beams under Thermo-Electro-Mechanical Loads2011 / A. Komeili, A. H. Akbarzadeh, A. Doroushi, M. R. Eslami