Mechanical engineering topic list of research papers
-
Development of a traffic noise prediction model for an urban environment2014 / Asheesh Sharma, GL Bodhe, G Schimak
-
The Influence of Different Recycling Scenarios on the Mechanical Design of an LED Weatherproof Light Fitting2014 / Víctor Camañes, Daniel Elduque, Carlos Javierre, Ángel Fernández
-
Modelling of Vibration Assisted Machining f.c.c Single Crystal
Abstract In this paper, a developed three-dimensional model combining finite-element and smoothed-particle hydrodynamics approaches is presented. It incorporates a crystal-plasticity theory for vibration-assisted machining into ABAQUS/Explicit...
2015 / S. Abolfazl Zahedi, Anish Roy, Vadim V. Silberschmidt -
A New Gaze Estimation Method Considering External Light2015 / Jong Lee, Hyeon Lee, Su Gwon, Dongwook Jung, Weiyuan Pan, et al.
-
District Heating Mode Analysis Based on an Air-cooled Combined Heat and Power Station2014 / Pei Li, Zhihua Ge, Zhiping Yang, Yuyong Chen, Yongping Yang
-
Combustion characteristics of lemongrass (Cymbopogon flexuosus) oil in a partial premixed charge compression ignition engine
Abstract Indeed, the development of alternate fuels for use in internal combustion engines has traditionally been an evolutionary process in which fuel-related problems are met and critical fuel properties are identified and their specific limits...
2015 / Avinash Alagumalai -
Adrenomedullin-RAMP2 System Suppresses ER Stress-Induced Tubule Cell Death and Is Involved in Kidney Protection2014 / Ryuichi Uetake, Takayuki Sakurai, Akiko Kamiyoshi, Yuka Ichikawa-Shindo, Hisaka Kawate, et al.
-
LPG diesel dual fuel engine – A critical review
Abstract The engine, which uses both conventional diesel fuel and LPG fuel, is referred to as ‘LPG–diesel dual fuel engines’. LPG dual fuel engines are modified diesel engines which use primary fuel as LPG and secondary fuel as diesel. LPG dual fuel ...
2015 / B. Ashok, S. Denis Ashok, C. Ramesh Kumar -
Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding
Abstract Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication (MQL), and nanoparticle jet MQL were used in the grinding ...
2015 / Dongkun Zhang, Changhe Li, Dongzhou Jia, Yanbin Zhang, Xiaowei Zhang -
Heat Release Analysis of Hydraulic Free Piston Diesel Engine
Abstract A simplified method is used to calculate the Rate of Heat Release (RoHR), some notice details are considered. The data is smoothed to get the final curves, we analyze the parameters of original formula of Wiebe and they are fitted the well...
2015 / Shuanlu Zhang, Changlu Zhao, Zhenfeng Zhao -
Design of passive fault-tolerant flight controller against actuator failures
Abstract The problem of designing passive fault-tolerant flight controller is addressed when the normal and faulty cases are prescribed. First of all, the considered fault and fault-free cases are formed by polytopes. As considering that the safety...
2014 / Xiang Yu, Youmin Zhang -
Sustainable Traffic Safety Management at Accident Black Spots Combined with Drivers’ Psychology and Vehicle Engineering Using Eye Mark Recorder
Abstract This paper proposes an integrated approach for sustainable traffic safety management at accident blackspots, including a mechanism that tracks the occurrence of accidents from the moment of drivers’ vision to actual accident occurrence, via ...
2014 / Hiroshi Wakabayashi, Masanori Ando, Tadashi Kawaguchi, Yuhki Horie, Kyo-hei Hotta -
Leukocyte margination at arteriole shear rate2014 / N. Takeishi, Y. Imai, K. Nakaaki, T. Yamaguchi, T. Ishikawa
-
Guest editorial of “Application of high strength steels in lightweight commercial vehicles”2015 / H. Mohrbacher
-
Indirect Method of the Critical Parameters of Frank-Kamenetskii Equations in Spontaneous Combustion Theory
Abstract The steady state heat balance equation in Frank-Kamenetskii model is one of the basic models of spontaneous combustion. For a non-uniform temperature exothermic reaction system met the Arrhenius law, the reaction heat term of the heat...
2016 / Yuan Yu, Quan-bing Luo, Dong Liang -
On the boundary conditions in multi-phase flow through the piston ring-cylinder liner conjunction
Abstract Prediction of load capacity and friction depends on the assumed boundary conditions. The inlet comprises swirl and counter flows, admitting only a portion of the inward flow into the conjunctional gap. At the contact exit, the lubricant...
2015 / H. Shahmohamadi, M. Mohammadpour, R. Rahmani, H. Rahnejat, C.P. Garner, et al. -
3D CFD Analysis of a Vertical Axis Wind Turbine2015 / Andrea Alaimo, Antonio Esposito, Antonio Messineo, Calogero Orlando, Davide Tumino
-
Characteristics Analysis and Testing of SMA Spring Actuator2013 / Jianzuo Ma, Haolei Huang, Jin Huang
-
Crack Detection in Single-Crystalline Silicon Wafer Using Laser Generated Lamb Wave2013 / Min-Kyoo Song, Kyung-Young Jhang
-
Vision Servo Motion Control and Error Analysis of a Coplanar Stage for Image Alignment Motion2013 / Hau-Wei Lee, Chien-Hung Liu