Materials engineering topic list of research papers
-
Load partitioning between the bcc-iron matrix and NiAl-type precipitates in a ferritic alloy on multiple length scales2016 / Zhiqian Sun, Gian Song, Thomas A. Sisneros, Bjørn Clausen, Chao Pu, et al.
-
Interactive effect of microstructure and cavity dimension on filling behavior in micro coining of pure nickel2016 / Chuanjie Wang, Chunju Wang, Jie Xu, Peng Zhang, Debin Shan, et al.
-
The Effect of Traverse Speed on Kerf Width in AWJ Cutting of Ceramic Tiles
Abstract This article describes experiments performed to assess the effectiveness of abrasive waterjet (AWJ) traverse used to cut ceramic tiles. As the process does not involve high forces, it is important to select the correct traverse speed to...
2017 / Daniel Krajcarz, Damian Bańkowski, Piotr Młynarczyk -
Wet Curtain Wall: A Novel Passive Radiant System for Hot and Dry Climates
Abstract This paper proposes a novel radiative passive system for hot and dry climates to improve outdoor thermal comfort. The solution consists in a curtain, characterized by two different finishing surfaces, one is waterproof and the other one is...
2017 / F. Butera, N. Aste, R.S. Adhikari, C. Del Pero, F. Leonforte, et al. -
Strength Properties of Grout for Strata Reinforcement
Abstract An experimental study was carried out on grout samples prepared from both Stratabinder and BU100 cementitious products. Samples were prepared with various water to grout ratios and tested for uniaxial compressive and shear strength....
2017 / Naj Aziz, Dean Majoor, Ali Mirzaghorbanali -
High-Temperature Decomposition of Fe- and Cr-Doped NiO Produced by a Novel Flame Spray Technique2017 / Mark E. Duffield, Gordon J. Tatlock, John F. Lewis
-
Three-dimensional adaptive finite-time guidance law for intercepting maneuvering targets
Abstract To intercept maneuvering targets at desired impact angles, a three-dimensional terminal guidance problem is investigated in this study. Because of a short terminal guidance time, a finite-time impact angle control guidance law is developed...
2017 / Yujie SI, Shenmin SONG -
Management Tool Design for Eco-efficiency Improvements in Manufacturing – A Case Study
Abstract As the worldwide GDP is forecasted to double by 2035, the energy demand globally is expected to increase by 34%. The industrial sector is also expected to account for more than 30% of the primary energy demand by 2040. These projections...
2017 / Lampros Litos, Fiammetta Borzillo, John Patsavellas, David Cockhead, Konstantinos Salonitis -
Evaluation of Thermal Efficiency of Membrane Distillation under Conductive Layer Integration
Abstract The role of high conductive layer integration in the performance of the of direct contact membrane distillation (DCMD) processes is investigated. In particular temperature polarization coefficient (TCP), mass flux and thermal efficiency are ...
2017 / Isam Janajreh, Raed Hashaikeh, Mohammed Noorul Hussain -
Comparison of aerodynamic characteristics between a novel highly loaded injected blade with curvature induced pressure-recovery concept and one with conventional design
Abstract This paper introduces a novel design method of highly loaded compressor blades with air injection. CFD methods were firstly validated with existing data and then used to develop and investigate the new method based on a compressor cascade....
2017 / Zhiyuan CAO, Chao ZHOU, Zhili SUN -
Integrating Environmental Impacts with SysML in MBSE Methods
Abstract The continuously growing integration of mechanics, electronics, and informatics into modern products introduces a considerable complexity into product development activities. Model-Based Systems Engineering (MBSE) methods are one approach...
2017 / Sébastien Bougain, Detlef Gerhard -
Effects of metal binder on the microstructure and mechanical properties of Al2O3-based micro-nanocomposite ceramic tool material2017 / Xiu-ying Ni, Jun Zhao, Jia-lin Sun, Feng Gong, Zuo-li Li
-
Determining the Potential to Improve Schedule Compliance
Abstract High schedule compliance is very important but rarely achieved in make-to-order productions. Especially when orders are released too late (e. g. due to missing raw material) it is challenging to identify how many orders can still be...
2017 / Andreas Piontek, Hermann Lödding -
Usage of the «BRNL-FT» program for foundation calculation using the method of the predefined equated soil settlements
Abstract The article considers the use of developed software, which is designed for spread foundation calculation using proposed method of predefined (by project designer) equated settlements. This method allows to decrease differential settlements...
2017 / S.I. Alekseev, S.O. Kondrat’ev -
The Scientific Challenges for a Sustainable Consumption and Production Scenario: The Circular Reuse of Materials for the Upgrading and Repurposing of Components
Abstract Beyond direct reuse and remanufacturing strategies, the upgrading and repurposing of products remain lot of added value to the products and transform the used products in new products with an improved performance or totally new. The paper...
2017 / Daniel Brissaud, Peggy Zwolinski -
Driving Cycle Development for Electric Vehicle Application using Principal Component Analysis and K-means Cluster: With the Case of Shenyang, China
Abstract Driving cycle is essential for the investigation of power management in electrified vehicles. Building a representative driving cycle remains a challenge due to the complex driving conditions. In this paper, the principal component analysis ...
2017 / Wenyu Zhou, Ke Xu, Ying Yang, Jiahuan Lu -
Explosive Energy Utilization Enhancement with Air-Decking and Stemming Plug, ‘SPARSH’
Abstract Engineering blasting is considered the most economical means of rock fragmentation. The explosive energy utilization is limited to 7% to 22% for fracturing and fragmentation though. The rest of energy components manifests itself into...
2017 / M.R. Saharan, M. Sazid, T.N. Singh -
Integration concepts for multi-organ chips: how to maintain flexibility?!2017 / Julia Rogal, Christopher Probst, Peter Loskill
-
Facile and controllable synthesis of BaCO 3 crystals superstructures using a CO 2 -storage material
Abstract We here report a new CO2 capture and storage method that converts CO2 into a novel alkyl carbonate salt, denoted as CO2SM, by a system consisting of equimolar 1,4-butanediol (BDO) and 1,2-ethylenediamine (EDA). This novel CO2SM was then...
2017 / Feng Sha, Bo Guo, Jing Zhao, Fei Zhang, Xianshu Qiao, et al. -
Diamond Lapping of Sapphire Wafer with Addition of Graphene in Slurry
Abstract In this paper, a novel method with addition of graphene in diamond slurry is proposed to conduct CMP lapping of sapphire wafer. Two kinds of graphenes are added including graphene oxide (GO), reduced graphene oxide (RGO). Effect of three...
2017 / Hsien-Kuang Liu, Chao-Chang A. Chen, Wei-Chung Chen