Materials engineering topic list of research papers
-
Modelling, Simulation and Optimization of the Materials Flow of a Multi-product Assembling Plant
Abstract Various dynamic factors impact the movement of materials within a manufacturing environment, increasingly becoming complex for multi-product assembling plants owing to the multiplicity and interconnectedness of these factors. Analyzing...
2017 / Wilson R. Nyemba, Charles Mbohwa -
‘In-situ’ Inspection Technologies: Trends in Degradation Assessment and Associated Technologies
Abstract The advent of advanced, innovative and complex engineered systems has established new technologies that are far more superior and perform well even in harsh environments. It is well established that such next generation systems need to be...
2017 / Sri Addepalli, Rajkumar Roy, Dragoş Axinte, Jörn Mehnen -
Formation of a quasicrystalline phase in Al–Mn base alloys cast at intermediate cooling rates2017 / Katarzyna Stan-Głowińska, Łukasz Rogal, Anna Góral, Anna Wierzbicka-Miernik, Joanna Wojewoda-Budka, et al.
-
The Numerical Analysis of the Hardening Phenomena of the Hot-work Tool Steel
Abstract In the paper, to the numerical analysis of quenching phenomena, the complex model of hardening of the hot-work tool steel is used. The numerical algorithm of the thermal phenomena is based on the solving of the heat transfer equation, which ...
2017 / Joanna Wróbel, Adam Kulawik, Adam Bokota -
Ab initio-aided CALPHAD thermodynamic modeling of the Sn-Pb binary system under current stressing2013 / Shih-kang Lin, Chao-kuei Yeh, Wei Xie, Yu-chen Liu, Masahiro Yoshimura
-
Reverse Engineering for the Rotor Blades of a Horizontal Axis Micro-hydrokinetic Turbine
Abstract The geometric data for a broken blade of a horizontal axis micro-hydrokinetic turbine were obtained by reverse engineering and, reconstructed model was validated by re-engineering process and experiment. A direct scanning procedure was...
2017 / Adrian Ciocănea, Sergiu Nicolaie, Corina Băbuţanu -
Microstructural Study of the Interfacial Transition Zone in Concrete using Optical Microscopy2017 / Khairul Nizar Ismail, Tan Let Hui
-
Announcement: A new journal from AIP Publishing—APL Materials2013 / Mark M. Cassar
-
Effect of chemical mechanical polishing on surface nature of titanium implants FT-IR and wettability data of titanium implants surface after chemical mechanical polishing implementation
Abstract Bioactivity of titanium depends on the quality and characteristics of its surface oxide film. Through implementation of chemical mechanical polishing (CMP) process on titanium plates, a protective oxide (titania) film grows on the titanium...
2016 / Zeynep Ozdemir, Gul Bahar Basim -
Exploration of the fragmentation of laser shock-melted aluminum using x-ray backlighting2016 / Lin Zhang, Ying-Hua Li, Xue-Mei Li, Xiang-Ping Ye, Zu-Gen Zhang, et al.
-
Controllable deposition distance of aligned pattern via dual-nozzle near-field electrospinning2017 / Zhifeng Wang, Xindu Chen, Jun Zeng, Feng Liang, Peixuan Wu, et al.
-
Impinging Air Jets on Flat Surfaces at Low Reynolds Numbers
Abstract Many practical applications and developing devices assume impinging jets to be spreading on smooth surfaces or in narrow gaps with controlled wall roughness. This work presents results of an experimental investigation and a CFD numerical...
2017 / Ştefan-Mugur Simionescu, Nicoleta-Octavia Tănase, Diana Broboană, Corneliu Bălan -
Research Progress towards Understanding the Unique Interfaces between Concentrated Electrolytes and Electrodes for Energy Storage Applications2017 / Jianming Zheng, Joshua A. Lochala, Alexander Kwok, Zhiqun Daniel Deng, Jie Xiao
-
Real Time Study of P&O MPPT Control for Small Wind PMSG Turbine Systems Using Arduino Microcontroller
Abstract Most papers discuss the simulation of the Maximum Power Point Tracking (MPPT) control “Perturb and Observe” (P&O), while its realization and execution in a control card remains a big challenge. Others have performed the implementation...
2017 / Badreddine Lahfaoui, Smail Zouggar, Bourhaleb Mohammed, Mohamed Larbi Elhafyani -
Application of Spindle Speed Increaser as Sustainable Solution to Upgrade Machine Tools
Abstract Due to varying machine operations, cutting material and feed motion of the respective milling machine, a wide range of spindle speed is required. Modern machine tools are therefore occasionally equipped with two spindles to cover a wider...
2017 / Eckart Uhlmann, Simon Thom, Matthias Ehricke -
Spectroscopic properties and luminescence behavior of γ-irradiated Sm 3+ doped oxy-fluoride phosphate glasses
Abstract Oxy-fluoride glasses singly and co-doped with Sm3+ ions have been synthesized of composition 30, 20 and 50mol% NaF, AlF3 and PF5, respectively, was established to study the effect of both Sm3+ ions concentrations(0.25–1mol%), and different...
2017 / Y.M. Hamdy, S. Bahammam, S. Abd El All, F.M. Ezz-Eldin -
Study of Solidification of Continuously Cast Steel Round Billets Using Numerical Modelling2016 / M. Tkadlečková, L. Válek, L. Socha, M. Saternus, J. Pieprzyca, et al.
-
Pressure-induced shift of Tc and structural transition in “122” type pnictide superconductor Ca0.34Na0.66Fe2As22016 / Sijia Zhang, Kan Zhao, Xiaohui Yu, Jinlong Zhu, Qingqing Liu, et al.
-
Optimisation Methodology of a Full-scale Active Twist Rotor Blade
Abstract This paper presents optimisation methodology for the design of the full scale rotor blade with an active twist to enhance its capability for vibration and noise reduction. This methodology is based on the 3Dfinite element model, planning of ...
2017 / Andrejs Kovalovs, Evgeny Barkanov, Sandris Ruchevskis, Miroslaw Wesolowski -
A fiber-optic Doppler blood flow-velocity sensor
Abstract A mock-up of а fiber-optic Doppler blood flow-velocity sensor has been made and described. The principle of its operation is based on the recording of the Doppler shift of scattered radiation of a monofrequent single-mode semiconductor...
2017 / Vitaliy I. Krasovskii, Ivan N. Feofanov, Pyotr I. Ivashkin, Mishik A. Kazaryan